PIN 6K1983 - Caterpillar

6K1983 PIN Caterpillar parts 977K, 977L

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA6K1983
6K-1983
6K1983

Weight: 17 pounds 7 kg.

Information:

EFFECTIVE LENGTH 62 mm

HEAD OD 0 mm

OVERALL LENGTH 214.5 mm

PIN OD 76.18 mm

TRANSV HOLES Y

DETENT BALL N

END TYPE A LEAD TAPER

END TYPE B LEAD TAPER

GROOVE N

HAND RING N

HEAD THICKNESS 0

KEEPER SLOT N

LUBE OUTLETS Y

COATING/PLATING 1E0586

THREAD SIZE MAX 1.25-12

Buy PIN 6K1983 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK LOADER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

CTP Caterpillar Pin (6k1983) Aftermarket

$67.22

13 May 2022
17.6369[7.94] Pounds
US: ProperBuy

CTP Caterpillar Pin (6k1983) Aftermarket
CTP

Show more prices Caterpillar parts

Number on catalog scheme: 13

For full view, you need register

Compatible equipment models: 6K1983:

TRACK LOADER 977K 977L Caterpillar

Information:

CX31–P600 Side PTO Petroleum Transmission
Illustration 1 g01998127
CX31–P600 (Side PTO Drive)
(1) Filter inlet pressure coupler (S O S port)
(2) Filter outlet pressure coupler
(3) Customer interface connector (70-pin)
(4) Lifting points, two (M16 X 2)
(5) SAE J615 mounting pads SAE #1 bolt pattern with 6 M16 x 2 threaded holes. SAE #2 width between mounting pads ( 520.7 mm (20.5 inch)).
(6) Conventional ten bolt PTO at 1:00 o'clock position
(7) Location of the identification and serial plate
(8) Oil filler and dipstick location
(9) Four M16x2 threaded service mounts
(10) Rear magnetic drain plug (SAE J1926 #12 port) (1 1/16 -12 O-ring face seal)
(11) Optional rear power take-off (RPTO) SAE "B" J744 pump drive and pilot. (Adapter required for 17 teeth Caterpillar spline), speed ratio 1.25:1
(12) Transmission output speed sensors
(13) SAE J1926 #4 auxiliary PTO control supply port (7/16 -12 O-ring face seal)
(14) Output yoke (1810 companion flange shown)
(15) Transmission mounted cartridge type oil filter
Illustration 2 g03429906
CX31–P600 (Side PTO Drive)
(5) SAE J615 mounting pads SAE #1 bolt pattern with 6 M16 x 2 threaded holes. SAE #2 width between mounting pads ( 520.7 mm (20.5 inch)).
(16) Crankshaft to flex plate adapter
(17) Flex plate
(18) Engine starter ring gear
(19) No. 1 SAE J617 flywheel housing (24 bolt)
(20) Conventional ten bolt PTO at 8:00 o'clock position
(21) Transmission breather
(22) Engine output speed sensor
(23) Torque converter output speed sensor
(24) Electronic Control Unit (ECU)
(25) Filter bypass switch
(26) Transmission oil temperature sensor (pump outlet and filter inlet)
(27) Location of oil level sensor connector
(28) Guard for the ECPC valves
(29) ECPC valves (six)
(30) SAE J1926 #16 inlet from cooler port (1 5/16 -12 O-ring face seal)
(31) SAE J1926 #16 outlet to cooler port (1 5/16 -12 O-ring face seal)
(32) Transmission main relief valve
(33) Drain plug SAE J1926 #16 port (1 5/16 -12 O-ring face seal) (Appropriate location for transmission oil heater)
Illustration 3 g03430323
CX31–P600 (Side PTO Drive)
(34) Transmission oil temperature sensor (converter outlet)
(35) Lockup clutch pressure coupler
(36) Clutch #1 (C1) pressure coupler
(37) C2 pressure coupler
(38) C3 pressure coupler
(39) C4 pressure coupler
(40) C5 pressure coupler
(41) Six base supports
(42) Three M8x1 bolts
(43) Access cover for magnetic filter and screen
(44) Lube pressure coupler CX31–P600 Side PTO Petroleum Transmission With Retarder
Illustration 4 g01998130
CX31–P600 (Side PTO Drive and Retarder)
(1) Filter inlet pressure coupler (S O S port)
(2) Filter outlet pressure coupler
(3) Customer interface connector (70-pin)
(4) Lifting points, two (M16 X 2)
(5) SAE J615 mounting pads SAE #1 bolt pattern with 6 M16 x 2 threaded holes. SAE #2 width between mounting pads ( 520.7 mm (20.5 inch)).
(6) Conventional ten bolt PTO at 1:00 o'clock position
(7) Location of the identification and serial plate
(8) Oil filler and dipstick location
(9) Four M16x2 threaded service mounts
(10) Rear magnetic drain plug (SAE J1926 #12 port) (1 1/16 -12 O-ring face seal)
(11) Optional rear power take-off (RPTO) SAE "B" J744 pump drive and pilot. (Adapter required for 17 teeth Caterpillar spline), speed ratio 1.25:1
(12) Transmission output speed sensors
(13) SAE J1926 #4 auxiliary PTO control supply port (7/16 -12 O-ring face seal)
(14) Output yoke (1810 companion flange shown)
(15) Transmission mounted cartridge type oil filter
(55) Diagnostic connector
Illustration 5 g03430425
CX31–P600 (Side PTO Drive and