PIN 6S3466 - Caterpillar

Engine3508C (S/N: PXA1-217; PXB1-278; TTP1-103)3512B (S/N: ED21-127; SRH1-104)3512C (S/N: RL21-103; SB21-100; DPC1-212; PXC1-250; PXE1-213; PXF1-390; PXG1-336; EWJ1-101; MXN1-223; MXP1-262; T3P1-421; TKP1-231; T3R1-345; T3S1-235; MNW1-100; PXW1-348; T3W1-279; TTW1-102; PXX1-211; T3Y1-200)3512E (S/N: MR21-206; MR41-203; MR81-208)3516C (S/N: BG31-105; DPD1-227; PXD1-207; PXH1-529; PXJ1-530; TKR1-257; TKS1-266; MXT1-218; TKT1-243; FLW1-103; TKX1-206; TKY1-359; TTY1-115; PXZ1-200; TTZ1-115)3516E (S/N: MD51-201; MR91-209; MRC1-242; MRN1-203)Description Of Change: A new duplex oil filter lever linkage assembly is now used on the engines that are listed above. The new linkage uses ball joint rod ends with seals to improve durability and increase service life.Adaptable To: The following changes are adaptable to the engines within the listed serial numbers, and are effective with all engines after the listed serial numbers.
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Rework Procedure
Follow the instructions below for installing the new oil filter lever linkage assembly.
Table 1
Required Parts
Item Qty New Part Number Description
1 2 0T-0924 Bolt
2 1 521-3763 Rod-Tie
3 4 532-8532 Seal-Rod End
4 4 5B-9079 Jam Nut
5 4 5M-2894 Hard Washer
6 2 7X-7875 Rod End
Illustration 1 g06277865
Remove the existing linkage. Inspect 4W-0096 Lever (handle) and 3D-9777 Lever (Duplex valve) for wear, replace if needed.
Illustration 2 g06277860
(1) 0T-0924 Bolt
(2) 532-8532 Seal-Rod End
(3) 7X-7875 Rod End
(4) 5M-2894 Hard Washer
(5) 4W-0096 Lever
(6) 5B-9079 Jam Nut
Assemble one jam nut (6) and one rod end (3) on each end of the 521-3763 Tie-Rod. Assemble the tie rod assembly to provide equal thread engagement on both rod ends.
Rotate the selector valve to the main run position until the valve touches the stop pin inside the cover assembly.
With the operator’s lever in the main run position, screw the plunger assembly into the lever until the plunger ball seats into the top hole in the mounting bracket.
Assemble the tie rod assembly onto lever (handle) (5), refer Illustration 2.
Illustration 3 g06280684
(1) 0T-0924 Bolt
(2) 532-8532 Seal-Rod End
(3) 7X-7875 Rod End
(4) 5M-2894 Hard Washer
(6) 5B-9079 Jam Nut
(7) 3D-9777 Lever
Assemble the tie rod assembly onto lever (Duplex Valve) (7) using bolt (1), hard washer (4), and jam nut (6), refer Illustration 3.
Adjust linkage to the lever and handle positions. Tighten all jam nut (6) to 30 5 N m (266 44 lb in).