6T7034 PIN-VALVE SPRING Caterpillar parts
3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 931B, C175-16, C175-20, D7G, G3512, G3516, G3516B, G3520B, PM3512, PM3516, PP3516
Rating:
Alternative (cross code) number:
CA6T7034
6T-7034
6T7034
CA6T7034
6T-7034
6T7034
Weight: 0.03 pounds 0 kg.
Information:
EFFECTIVE LENGTH
38
mm
HEAD OD
12.7
mm
OVERALL LENGTH
40
mm
PIN OD
6.1
mm
TRANSV HOLES
Y
DETENT BALL
N
END TYPE A
FLT
END TYPE B
FLT
GROOVE
N
HAND RING
N
HEAD THICKNESS
2
KEEPER SLOT
N
LUBE OUTLETS
N
GAS ENGINE, TRACK-TYPE TRACTOR,
Compatible equipment models: 6T7034:
Information:
Assembly Procedure
Table 1
Required Tools
Tooling Part Number Description Qty
A 1P-0510 Driver 1
B 3H-0467 Puller Washer 1
C 9S-9152 Bearing Puller 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00999802Note: Align the oil holes in bearings (1) and (2) with the oil holes in housing (3).
Use Tooling (A) in order to install bearing (1). Ensure that bearing (1) is flush with the face of the housing.
If bearing (2) was removed, use Tooling (A) in order to install bearing (2) to the bottom of the bearing bore.
Illustration 2 g00999804
Place shaft assembly (5) into position in housing (3). Place Tooling (B) under the gear on shaft assembly (5) for support. Note: Use a new sleeve when you replace sleeve (4).
Use a press in order to install new sleeve (4) on shaft assembly (5), as shown.
Illustration 3 g00999805
If bearing (6) was removed, use Tooling (A) in order to install bearing (6). Bearing (6) must be flush with the face of gear (7).
Illustration 4 g00999806
Place gear (7) in position over shaft (8).
Illustration 5 g00999808
If seal (9) was removed, use Tooling (A) in order to install seal (9) to the bottom of the seal bore with the lip of the seal toward the inside. Apply a small amount of engine oil on seal (9).
If bushing (10) was removed, use Tooling (A) in order to install bushing (10) to the bottom of the bushing bore.
Illustration 6 g00999809
If bearing (11) was removed from adapter (12), use Tooling (A) in order to install bearing (11) even with the face of adapter (12).
Illustration 7 g00999810
Install the key on shaft (13).
Use a press and Tooling (C) in order to push gear (14) on shaft (13) until the holes in the gear and the shaft are in alignment.
Illustration 8 g00999811
Install taper pin (15) that holds gear (14) in place.
Illustration 9 g00999813
Install a new gasket and adapter (12) on housing (3).
Place shaft (13) and the gear into position in adapter (12).
Illustration 10 g00999814
Install O-ring seal (16) on housing (3). Apply a small amount of engine oil on O-ring seal (16). End By:
Install the magneto drive. Refer to Disassembly and Assembly, "Magneto Drive - Remove and Install".
Table 1
Required Tools
Tooling Part Number Description Qty
A 1P-0510 Driver 1
B 3H-0467 Puller Washer 1
C 9S-9152 Bearing Puller 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00999802Note: Align the oil holes in bearings (1) and (2) with the oil holes in housing (3).
Use Tooling (A) in order to install bearing (1). Ensure that bearing (1) is flush with the face of the housing.
If bearing (2) was removed, use Tooling (A) in order to install bearing (2) to the bottom of the bearing bore.
Illustration 2 g00999804
Place shaft assembly (5) into position in housing (3). Place Tooling (B) under the gear on shaft assembly (5) for support. Note: Use a new sleeve when you replace sleeve (4).
Use a press in order to install new sleeve (4) on shaft assembly (5), as shown.
Illustration 3 g00999805
If bearing (6) was removed, use Tooling (A) in order to install bearing (6). Bearing (6) must be flush with the face of gear (7).
Illustration 4 g00999806
Place gear (7) in position over shaft (8).
Illustration 5 g00999808
If seal (9) was removed, use Tooling (A) in order to install seal (9) to the bottom of the seal bore with the lip of the seal toward the inside. Apply a small amount of engine oil on seal (9).
If bushing (10) was removed, use Tooling (A) in order to install bushing (10) to the bottom of the bushing bore.
Illustration 6 g00999809
If bearing (11) was removed from adapter (12), use Tooling (A) in order to install bearing (11) even with the face of adapter (12).
Illustration 7 g00999810
Install the key on shaft (13).
Use a press and Tooling (C) in order to push gear (14) on shaft (13) until the holes in the gear and the shaft are in alignment.
Illustration 8 g00999811
Install taper pin (15) that holds gear (14) in place.
Illustration 9 g00999813
Install a new gasket and adapter (12) on housing (3).
Place shaft (13) and the gear into position in adapter (12).
Illustration 10 g00999814
Install O-ring seal (16) on housing (3). Apply a small amount of engine oil on O-ring seal (16). End By:
Install the magneto drive. Refer to Disassembly and Assembly, "Magneto Drive - Remove and Install".
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
6S3759
PIN AS
910, 931, 931B, 931C, 933C, 935B, 935C, 939C
910, 931, 931B, 931C, 933C, 935B, 935C, 939C
2M3521
PIN
814B, 815B, 824C, 826C, 931B, 950B, 950B/950E, 955H, 963, 973, 977H, 977K, 983, D4, D6C, D7G, D8H, PIN GRAB
814B, 815B, 824C, 826C, 931B, 950B, 950B/950E, 955H, 963, 973, 977H, 977K, 983, D4, D6C, D7G, D8H, PIN GRAB
7K9360
PIN
910, 931B, 941, 951B, IT12, IT12B
910, 931B, 941, 951B, IT12, IT12B
3D6509
PIN
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
3K2510
PIN
14E, 572G, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 776C, 776D, 777B, 777D, 777F, 777G, 814, 950, 955H, 955K, 955L, 966C, 983, D5, D5B, D7F, D7G, D7G2
14E, 572G, 627, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637B, 637D, 637E, 637G, 776C, 776D, 777B, 777D, 777F, 777G, 814, 950, 955H, 955K, 955L, 966C, 983, D5, D5B, D7F, D7G, D7G2
6S3466
PIN
910, 931B
910, 931B
6S3473
PIN ASSEM.
910, 931B, PM-465
910, 931B, PM-465
5G4066
PIN
910, 931B, IT12, IT12B, IT14B, IT14F
910, 931B, IT12, IT12B, IT14B, IT14F
4J5240
PIN
D7E, D7E LGP, D7F, D7G, D7G2, D7H, D7R, D7R II, D7R XR
D7E, D7E LGP, D7F, D7G, D7G2, D7H, D7R, D7R II, D7R XR
3J6182
PIN ASSEM.
D7F, D7G, D7G2, D7H
D7F, D7G, D7G2, D7H
3J6502
PIN
7A, D7G, D7G2
7A, D7G, D7G2
6J6229
PIN
7A, 7S, D7G, D7G2
7A, 7S, D7G, D7G2
1P5274
PIN-VALVE SPRING
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 1693, 16G, 16H, 16H NA, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 5130B, 5230, 641B, 657B, 666B, 769C, 776, 777, 793B,...
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 1693, 16G, 16H, 16H NA, 3508, 3508B, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 3606, 3608, 3612, 3616, 5130B, 5230, 641B, 657B, 666B, 769C, 776, 777, 793B,...
2W5974
PIN
3508, 3512, 3516, 3606, 3608, 3612, 3616, 785, C280-12, C280-16, C280-6, C280-8
3508, 3512, 3516, 3606, 3608, 3612, 3616, 785, C280-12, C280-16, C280-6, C280-8
2339234
PIN-CONNECTOR
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
8N1542
PIN-CONNECTOR
1090, 1190, 1190T, 1290T, 1390, 227, 2290, 2390, 2391, 245, 2470C, 2491, 24M, 2570C, 2590, 2670C, 2864C, 305.5, 306, 306E, 311F LRR, 3126B, 320B FM LL, 325B L, 325C, 325D MH, 330B L, 330C MH, 330D MH,...
1090, 1190, 1190T, 1290T, 1390, 227, 2290, 2390, 2391, 245, 2470C, 2491, 24M, 2570C, 2590, 2670C, 2864C, 305.5, 306, 306E, 311F LRR, 3126B, 320B FM LL, 325B L, 325C, 325D MH, 330B L, 330C MH, 330D MH,...
2339233
PIN-CONNECTOR
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
2339232
PIN-CONNECTOR
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C
7W5599
PIN
3116, 3126, 928F, IT28F
3116, 3126, 928F, IT28F
6L2244
PIN
3406, 3406B, 3516, 769C, 769D, 771C, 771D, 773B, 773D, 773F, 775B, 775D, 775F, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, AE40 II, D342, D342C, D350E, D350E II, D400E, D400E II, D40D
3406, 3406B, 3516, 769C, 769D, 771C, 771D, 773B, 773D, 773F, 775B, 775D, 775F, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, AE40 II, D342, D342C, D350E, D350E II, D400E, D400E II, D40D
8L5200
PIN
3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, D348, D399, G399
3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, D348, D399, G399
8L5199
PIN
3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, D348, D399, G399
3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, D348, D399, G399
1014135
PIN-SPRING
30/30, 3508B, 3512, 3512B, 3516, 3516B, 5130, 5230, 777D, 785C, 789C, 793, 793B, 793D, 854G, 992G, D11R, DEUCE
30/30, 3508B, 3512, 3512B, 3516, 3516B, 5130, 5230, 777D, 785C, 789C, 793, 793B, 793D, 854G, 992G, D11R, DEUCE
5N9012
PIN-COTTER
3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C
3508B, 3508C, 3512, 3512B, 3516, 3516B, 3516C