6Y2143 PIN-TRACK Caterpillar parts
65C, D9N, D9R
Rating:
Alternative (cross code) number:
CA6Y2143
6Y-2143
6Y2143
CA6Y2143
6Y-2143
6Y2143
Weight: 8 pounds 3 kg.
CHALLENGER, TRACK-TYPE TRACTOR,
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1861 Retaining Ring Pliers 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Verify correct assembly of the pistons and the connecting rods. Ensure that the etched numbers on the rod and the rod cap are in the correct positions. The etched number on the rod and the rod cap correspond to the cylinder in which it should be installed.
Note: For information on reusability of the pistons, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8049, "Pistons"
Guideline For Reusable Parts And Salvage Operations, SEBF8228, "Procedure to Clean and Inspect One and Two-Piece Pistons in 3114/3116 Engines"
Guideline For Reusable Parts And Salvage Operations, SEBF8290, "Visual Inspection of Two-Piece Pistons"
Tool Operating Manual, NEHS0775, "Using the 186-0137 Pston Ring Gauge on Steel Crown, Two-Piece Pistons used in 3126 Engines"Note: For information on reusability of the connecting rods, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8206, "Specificatios for ConnectingRods on 3116 Engines"
Guideline For Reusable Parts And Salvage Operations, SEBF8063, "Visual Inspection of Connecting Rods"
Guideline For Reusable Parts And Salvage Operations, SEBF8064, "Salvage of Non-Serrated Connecting Rods"Note: For information on reusability of the piston pins, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8051, "Piston Pins and Retaining Rings"
Guideline For Reusable Parts And Salvage Operations, SEBF8303, "Procedure to Inspect Piston Pins"Note: For information on reusability of the rod eye bushing, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8242, "Verification of Connecting Rod Eye Bushing Retention Using 5P-8639 Connecting Rod Bushing Press Group"
Guideline For Reusable Parts And Salvage Operations, SEBF8274, "Using Rod Eye Bushing Installation and Removal Tools"
Illustration 1 g00610428
Check the clearance between the ends of piston rings (5). Refer to the Specifications Manual, "Pistons and Rings". Note: The oil ring must be installed over the spring with the end gap 180 degrees from the oil ring spring joint.
Install the oil control piston ring with Tooling (A). The ends of the spring should be rotated 180 degrees from the ring end gap.
Install the intermediate piston ring with the side marked "UP-2" toward the top of the piston. Use Tooling (A) in order to install the ring.
Install the top piston ring with the side marked "UP-1" toward the top of the piston. Use Tooling (A) in order to install the ring.
Illustration 2 g00610498
Replace rod bearing (6) by pressing a new bearing into the connecting rod. Refer to Special Instruction, SEHS7295 for the correct tooling and the correct installation procedure.
Illustration 3 g00641764
One piece piston
Illustration 4 g00610503
This piston is a two-piece assembly. This piston consists of piston crown (7) and piston skirt (8). Inspect bearing (9) in the piston crown (7). The piston crown must be replaced if the piston crown is worn or damaged. Bearing (9) is nonserviceable.
Illustration 5 g00678083
Position piston (1) on connecting rod (3). Coat piston pin (4) with clean engine oil and install piston pin (4).
Illustration 6 g00678081
Use Tooling (B) to install the retaining
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1861 Retaining Ring Pliers 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Verify correct assembly of the pistons and the connecting rods. Ensure that the etched numbers on the rod and the rod cap are in the correct positions. The etched number on the rod and the rod cap correspond to the cylinder in which it should be installed.
Note: For information on reusability of the pistons, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8049, "Pistons"
Guideline For Reusable Parts And Salvage Operations, SEBF8228, "Procedure to Clean and Inspect One and Two-Piece Pistons in 3114/3116 Engines"
Guideline For Reusable Parts And Salvage Operations, SEBF8290, "Visual Inspection of Two-Piece Pistons"
Tool Operating Manual, NEHS0775, "Using the 186-0137 Pston Ring Gauge on Steel Crown, Two-Piece Pistons used in 3126 Engines"Note: For information on reusability of the connecting rods, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8206, "Specificatios for ConnectingRods on 3116 Engines"
Guideline For Reusable Parts And Salvage Operations, SEBF8063, "Visual Inspection of Connecting Rods"
Guideline For Reusable Parts And Salvage Operations, SEBF8064, "Salvage of Non-Serrated Connecting Rods"Note: For information on reusability of the piston pins, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8051, "Piston Pins and Retaining Rings"
Guideline For Reusable Parts And Salvage Operations, SEBF8303, "Procedure to Inspect Piston Pins"Note: For information on reusability of the rod eye bushing, refer to the following list.
Guideline For Reusable Parts And Salvage Operations, SEBF8242, "Verification of Connecting Rod Eye Bushing Retention Using 5P-8639 Connecting Rod Bushing Press Group"
Guideline For Reusable Parts And Salvage Operations, SEBF8274, "Using Rod Eye Bushing Installation and Removal Tools"
Illustration 1 g00610428
Check the clearance between the ends of piston rings (5). Refer to the Specifications Manual, "Pistons and Rings". Note: The oil ring must be installed over the spring with the end gap 180 degrees from the oil ring spring joint.
Install the oil control piston ring with Tooling (A). The ends of the spring should be rotated 180 degrees from the ring end gap.
Install the intermediate piston ring with the side marked "UP-2" toward the top of the piston. Use Tooling (A) in order to install the ring.
Install the top piston ring with the side marked "UP-1" toward the top of the piston. Use Tooling (A) in order to install the ring.
Illustration 2 g00610498
Replace rod bearing (6) by pressing a new bearing into the connecting rod. Refer to Special Instruction, SEHS7295 for the correct tooling and the correct installation procedure.
Illustration 3 g00641764
One piece piston
Illustration 4 g00610503
This piston is a two-piece assembly. This piston consists of piston crown (7) and piston skirt (8). Inspect bearing (9) in the piston crown (7). The piston crown must be replaced if the piston crown is worn or damaged. Bearing (9) is nonserviceable.
Illustration 5 g00678083
Position piston (1) on connecting rod (3). Coat piston pin (4) with clean engine oil and install piston pin (4).
Illustration 6 g00678081
Use Tooling (B) to install the retaining
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
6J6680
PIN
8B, 8D, 9B, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
8B, 8D, 9B, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
3G7016
PIN
834G, 834H, 844, 844H, 844K, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
834G, 834H, 844, 844H, 844K, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
4T7534
PIN
834G, 834H, 834K, 844, 844H, 844K, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
834G, 834H, 834K, 844, 844H, 844K, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
7T4865
PIN
D8N, D8R, D8R II, D9N, D9R, D9T
D8N, D8R, D8R II, D9N, D9R, D9T
6Y3394
PIN-G.E.T.
320D, 320D GC, 320D L, 320D LRR, 320D RR, 325, 330 L, 375 L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
320D, 320D GC, 320D L, 320D LRR, 320D RR, 325, 330 L, 375 L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
4T0202
PIN AS
D7H, D7R, D7R II, D7R XR, D8L, D9N, D9R
D7H, D7R, D7R II, D7R XR, D8L, D9N, D9R
1U2472
PIN
844, 844H, 844K, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
844, 844H, 844K, D8L, D8N, D8R, D8R II, D8T, D9N, D9R, D9T
9P6912
PIN
D8L, D9N, D9R, D9T
D8L, D9N, D9R, D9T
1029062
PIN AS-G.E.T.
854G, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9R
854G, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9R
6Y1204
PIN-G.E.T.
375, 854G, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9R, D9T
375, 854G, D10N, D10R, D10T, D10T2, D11N, D11R, D11T, D9R, D9T
7T9308
PIN AS-CARTRIDGE
D8R, D9R
D8R, D9R
2663152
PIN AS-CARTRIDGE
D8R, D8R II, D8T, D9R, D9T
D8R, D8R II, D8T, D9R, D9T
9R8362
PIN AS
416
416
6I2718
PIN-PISTON
3176B, 3176C, 345B II, 345B L, 75C
3176B, 3176C, 345B II, 345B L, 75C
1265708
PIN
438B
438B
8N1544
PIN-CONNECTOR
120M, 12M, 16M, 2290, 2390, 2391, 2470C, 2491, 24M, 2570C, 2590, 2670C, 306E, 308E2 CR, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 3508B, 3512, 3512B, 3516B, 365C, 365C L, 374D L, 37...
120M, 12M, 16M, 2290, 2390, 2391, 2470C, 2491, 24M, 2570C, 2590, 2670C, 306E, 308E2 CR, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 3508B, 3512, 3512B, 3516B, 365C, 365C L, 374D L, 37...
9R8583
PIN
428B
428B
9R8734
PIN
426B
426B
0897500
PIN
RT100, RT50
RT100, RT50
0815498
PIN
RT100
RT100
1567433
PIN
RT100
RT100
8Q2131
PIN
RT100
RT100
9U2068
PIN
65C
65C