8E4708 PIN Caterpillar parts
365B, 365B II, 365C, 365C L, 365C L MH, 375, 385B, 385C, 385C FS, 385C L, 5080, 5090B, 5130, 980H, 980K, 994, 994D, 994F, 994H, D11R, D11T
Rating:
Alternative (cross code) number:
CA8E4708
8E-4708
8E4708
CA8E4708
8E-4708
8E4708
Weight: 2 pounds 0 kg.
Information:
HEAD DIAMETER
45
mm
OVERALL LENGTH
135
mm
PIN DIAMETER
32
mm
PIN LENGTH
125
mm
WITHOUT GROOVE
0
EXCAVATOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Bucket Tooth Pin fits Caterpillar 8E4708
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Bucket Tooth Pin fits Caterpillar 8E4708
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
National 1 Track & Parts We use precision manufacturing to deliver the highest quality parts
Compatible equipment models: 8E4708:
Information:
Illustration 1 g00573143
LH/RH Temperature Sender (Inlet Air)Note: Ensure that the desired diagnostic code (CID FMI) is on hold. Ensure that the "SERV CODE" indicator is ON. Use the electrical system schematic for the engine that is being serviced to find the connector contact on the Main Display Module which corresponds to the CID that is currently shown.This diagnostic code is recorded when the Main Display Module reads the voltage of the sender signal as being too low. The corresponding Gauge Needle is in the warning region as a result of this diagnostic condition. The following examples are possible causes.
The inlet air temperature sender unit has a problem.
The signal circuit for the inlet air temperature sender unit in the engine harness is shorted to ground.
The Main Display Module has a problem.Note: The Main Display Module is unable to determine when a sender or sender signal harness is open or the resistance is too high. This condition causes the corresponding Gauge Needle to stay at the left side of the scale.
Measure the Resistance of the Sender.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the inlet air temperature sender unit.
Measure the resistance that is between the two contacts of the sender connector. The following table illustrates the correct approximate resistance at various temperatures.
Table 1
Approximate Resistances For The Sender Connector Contacts    
Temperature     Resistance    
25 2°C (77 3.6°F)     1000 Ohms    
100 2°C (212 3.6°F)     103.7 Ohms    
Check the Display Area and the Harness.
Turn the "ECS" switch to the OFF/RESET position.
Check for loose connections or corroded connections to the inlet air temperature sender.
Replace corroded contacts and tighten loose connections.
Turn the "ECS" switch to the COOLDOWN/STOP position. The "SERV CODE" indicator should be ON for the diagnostic code CID 172 FMI 04.
Disconnect the engine harness from the inlet air temperature sender unit. Observe the "SERV CODE" indicator.Expected Result: The "SERV CODE" indicator should turn OFF.Results:
OK - The "SERV CODE" indicator turns OFF. The inlet air temperature sender unit has a problem. Replace the inlet air temperature sender unit.
Not OK - The SERV CODE indicator stays ON. The harness wiring or the Main Display Module has a problem. Proceed to Step 3.
Check the Sender Wire for a Short to Ground.
Turn the "ECS" switch to the OFF/RESET position.
Disconnect the engine harness from the inlet air temperature sender unit.
Turn the "ECS" switch to the COOLDOWN/STOP position.
Measure the voltage of the harness signal wire from the inlet air temperature sender unit. The voltage should be measured from pin 1 to pin 2 (ground).Expected Result: The voltage should be 6.0 0.5 DCV.Results:
OK - The voltage is 6.0 0.5 DCV. The voltage is correct. If the SERV CODE indicator is still ON, repeat Step 1 through Step 3. If the cause of the diagnostic fault is not found, replace the Main Display Module.
Not OK - If the voltage is less than 0.5 DCV, the harness wiring has a problem. There is an open circuit, a
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
2123092
PIN AS
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 385C
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B, 365B II, 365B L, 365C, 365C L, 385C
2343962
PIN AS
385B, 385C, 385C L
385B, 385C, 385C L
1304360
PIN AS
345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B
345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B
4I6721
PIN
350, 365B, 365B II, 365B L
350, 365B, 365B II, 365B L
1413477
PIN
345B II, 345B II MH, 345B L, 365B II, 385B
345B II, 345B II MH, 345B L, 365B II, 385B
1413476
PIN
345B II, 345B II MH, 345B L, 365B II, 385B
345B II, 345B II MH, 345B L, 365B II, 385B
1413550
PIN AS
345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 385B
345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, 365B II, 385B
1499427
PIN
365B, 365B L
365B, 365B L
3739528
PIN AS
325C, 325D L, 330C, 330D L, 345B II, 345C L, 365B, 365B II, 365C, 365C L, 385B, 385C L
325C, 325D L, 330C, 330D L, 345B II, 345C L, 365B, 365B II, 365C, 365C L, 385B, 385C L
2122896
PIN AS
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L
365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 385B, 385C, 385C L
1955476
PIN AS
365B, 365B II, 365B L, 365C, 365C L, 374D L, 385B, 385C, 385C L
365B, 365B II, 365B L, 365C, 365C L, 374D L, 385B, 385C, 385C L
1955580
PIN AS
365C, 385B, 385C, 385C L, 390D, 390D L, 390F L
365C, 385B, 385C, 385C L, 390D, 390D L, 390F L
1760801
PIN AS
994, 994D
994, 994D
1389320
PIN AS
994, 994D
994, 994D
1389322
PIN AS
994, 994D
994, 994D
1366783
PIN AS
5130, 994, 994D, 994F
5130, 994, 994D, 994F
1324788
PIN-FLEXIBLE
5130, 5130B, 5230, 994, 994D
5130, 5130B, 5230, 994, 994D
1341808
PIN-G.E.T.
375 L, 385B, 390D, 994, 994D, 994F
375 L, 385B, 390D, 994, 994D, 994F
1139688
PIN
5130, 994, 994D
5130, 994, 994D