8W9610 PIN Caterpillar parts
789, 789B, 793, 793B
Rating:
Alternative (cross code) number:
CA8W9610
8W-9610
8W9610
CA8W9610
8W-9610
8W9610
Weight: 62 pounds 28 kg.
Information:
OVERALL LENGTH
300
mm
OUTSIDE PIN DIAMETER
126.975
mm
END TYPE A
CHAMFER
END TYPE B
CHAMFER
FLAT/VENTED
N
INSIDE DIAMETER
27.5
TRUCK,
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure (Engines with Flywheel Housing and Back plate)
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Support the engine with a suitable lifting device or support the engine on blocks that are positioned on a flat level surface.
Install tool (A) and a suitable lifting device to the flywheel housing. Support the weight of the housing (8).
Illustration 1 g00827061
Typical example
Remove the setscrews (3) that fasten the flywheel housing (8) to the cylinder block.
Remove the setscrews (5) on each side of the cylinder block. These setscrews fasten the flywheel housing (8) to the cylinder block.
Remove the setscrews (1) that fasten the back plate (2) to the flywheel housing (8).
Remove the nuts (7) and the bolts (not shown) that fasten the back plate (2) to the flywheel housing (8).
Illustration 2 g00826988
Typical example
Use tool (A) and the lifting device to remove the flywheel housing (8) from the back plate. Removal Procedure (Engines with Flywheel Housing)
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The two cylinder, the three cylinder and the four cylinder engines have different flywheel housings. The removal procedure is similar for all models.
Support the engine with a suitable lifting device or support the engine on blocks that are positioned on a flat level surface.
Install tool (A) and a suitable lifting device to the flywheel housing. Support the weight of the housing (2).
Illustration 3 g01123577
Typical example
Remove the setscrews (1) that fasten the flywheel housing (2) to the cylinder block.
Illustration 4 g01126979
Use the tool (A) and the lifting device to remove the flywheel housing (2) from the engine. Installation Procedure (Engines with Flywheel Housing and Back plate)
Table 3
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 5 g00827061
Typical example
Clean the rear face of the back plate (2) and the faces of the flywheel housing (8). Inspect the crankshaft rear seal (not shown) for leaks. Inspect the dowels (6) for damage. If the crankshaft rear seal or the dowels are damaged, use new parts for replacement. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and Disassembly
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Support the engine with a suitable lifting device or support the engine on blocks that are positioned on a flat level surface.
Install tool (A) and a suitable lifting device to the flywheel housing. Support the weight of the housing (8).
Illustration 1 g00827061
Typical example
Remove the setscrews (3) that fasten the flywheel housing (8) to the cylinder block.
Remove the setscrews (5) on each side of the cylinder block. These setscrews fasten the flywheel housing (8) to the cylinder block.
Remove the setscrews (1) that fasten the back plate (2) to the flywheel housing (8).
Remove the nuts (7) and the bolts (not shown) that fasten the back plate (2) to the flywheel housing (8).
Illustration 2 g00826988
Typical example
Use tool (A) and the lifting device to remove the flywheel housing (8) from the back plate. Removal Procedure (Engines with Flywheel Housing)
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1 Start By:
Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: The two cylinder, the three cylinder and the four cylinder engines have different flywheel housings. The removal procedure is similar for all models.
Support the engine with a suitable lifting device or support the engine on blocks that are positioned on a flat level surface.
Install tool (A) and a suitable lifting device to the flywheel housing. Support the weight of the housing (2).
Illustration 3 g01123577
Typical example
Remove the setscrews (1) that fasten the flywheel housing (2) to the cylinder block.
Illustration 4 g01126979
Use the tool (A) and the lifting device to remove the flywheel housing (2) from the engine. Installation Procedure (Engines with Flywheel Housing and Back plate)
Table 3
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 5 g00827061
Typical example
Clean the rear face of the back plate (2) and the faces of the flywheel housing (8). Inspect the crankshaft rear seal (not shown) for leaks. Inspect the dowels (6) for damage. If the crankshaft rear seal or the dowels are damaged, use new parts for replacement. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove" and Disassembly
Caterpillar parts catalog:
Parts pin Caterpillar catalog:
621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 69D, 735, 740, 769D, 770, 771D, 772, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777D, 777F...
12M 3, 12M 3 AWD, 140M 3, 140M 3 AWD, 160M 3, 160M 3 AWD, 307, 307B, 307C, 307D, 308C, 308D, 308E, 308E CR, 308E SR, 311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L,...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 14...
16, 315D L, 316E L, 318D2 L, 318E L, 319D L, 319D LN, 320D, 320D GC, 320D L, 320D LRR, 320D RR, 320D2, 320E, 320E L, 320E LN, 320E LRR, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 324D, 324D L, 324E, ...
14H, 14H NA, 16H, 16H NA, 518, 518C, 528, 528B, 530B, 611, 613, 613B, 613C, 613C II, 615, 615C, 621, 621B, 621E, 621F, 621H, 621K, 623E, 623F, 623H, 623K, 623K LRC, 627E, 627F, 627H, 627K, 627K LRC, 6...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
611, 615, 615C, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631E, 633E II, 637E, 651E, 657E, 69D, 768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776C, 776D, 777B, 77...
621F, 623E, 623F, 627F, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776D, 777, 777B, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 994
621F, 623E, 623F, 627F, 69D, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776D, 777, 777B, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 994
769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 773B, 773D, 773E, 773F, 773G, 773G LRC, 775B, 775D, 775E, 775F, 775G, 775G LRC, 776C, 777, 777B, 777D, 777F, 777G, 785, 785B, 785C, 78...
793, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F-XQ
785, 785B, 785C, 785D, 789, 789B, 789C, 789D
8X5308
PIN
793, 793B
793, 793B
0951313
PIN-CLEVIS
789C, 789D, 793B, 793C, 793D, 795F AC, 795F XQ, 797F
789C, 789D, 793B, 793C, 793D, 795F AC, 795F XQ, 797F
785B, 785C, 785D, 789B, 789C, 789D
8X5446
PIN
785, 785B, 789, 793, 793B
785, 785B, 789, 793, 793B
6G9477
PIN
785, 785B, 785C, 785D, 789, 789B, 789C, 789D
785, 785B, 785C, 785D, 789, 789B, 789C, 789D
785, 785B, 785C, 785D, 789, 789B, 789C, 789D
9D2205
PIN
772, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
772, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
789B, 789C
1335619
PIN
789B
789B
8X5022
PIN
789, 789B, 789C, 789D
789, 789B, 789C, 789D
1335620
PIN
793B, 793C
793B, 793C
1195119
PIN
793B
793B