9U9229 PIN Caterpillar parts
572R, 572R II, 583R, 583T, 587R, 587T, D6R II, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T, PL83, PL87
Rating:
Alternative (cross code) number:
CA9U9229
9U-9229
9U9229
CA9U9229
9U-9229
9U9229
Weight: 5 pounds 2 kg.
Information:
EFFECTIVE LENGTH
143
mm
HEAD OD
50
mm
OVERALL LENGTH
160
mm
PIN OD
47.8
mm
TRANSV HOLES
N
DETENT BALL
N
END TYPE A
FLT
END TYPE B
CHAMFER
GROOVE
Y
HAND RING
N
HEAD THICKNESS
9
KEEPER SLOT
N
LUBE OUTLETS
N
COATING/PLATING
1E0586
THREAD SIZE MAX
.62-11
PIPELAYER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 9U9229:
Information:
MID 039 CID 1405 FMI 05Conditions Which Generate This Code:
Illustration 1 g01335076
Connections of the transmission clutch solenoid 5
This diagnostic code is associated with the transmission clutch solenoid 5. The FMI 05 means that the ECM has determined that an open in the circuit exists.The possible causes of this diagnostic code are listed below:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1405 FMI 05 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire J834-PU(Purple)) to contact 2 (wire H802-GY(Grey)).
Observe the status of the diagnostic code. Expected Result:The diagnostic code is active. Then, the diagnostic code changes from FMI 05 to FMI 06 as the jumper wire is installed.Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOPTest Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector(s) from the ECM.
The jumper wire that was installed in the previous Test Step remains in place.
At the machine harness connector, measure the resistance from signal contact J2-15 to contact J2-49. Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connector for the solenoid and the ECM connectors remain disconnected.
Remove the jumper wire that was installed in the last test step.
At the J2 connector for the ECM, use a wire removal tool to remove wire J834-PU(Purple) from contact J2-15.
Reconnect the machine harness connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Use a multimeter probe that is not connected to a multimeter or a similar device to make contact with the ECM at contact J2-15 through the empty space in the J2 connector.
Observe the status of the diagnostic code. Ground the other end of the multimeter probe
Illustration 1 g01335076
Connections of the transmission clutch solenoid 5
This diagnostic code is associated with the transmission clutch solenoid 5. The FMI 05 means that the ECM has determined that an open in the circuit exists.The possible causes of this diagnostic code are listed below:
The energize circuit of the solenoid is open.
The return circuit of the solenoid is open.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1405 FMI 05 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire J834-PU(Purple)) to contact 2 (wire H802-GY(Grey)).
Observe the status of the diagnostic code. Expected Result:The diagnostic code is active. Then, the diagnostic code changes from FMI 05 to FMI 06 as the jumper wire is installed.Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Replace the solenoid. Verify that the new solenoid corrects the problem.STOPTest Step 2. CHECK THE HARNESS FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector(s) from the ECM.
The jumper wire that was installed in the previous Test Step remains in place.
At the machine harness connector, measure the resistance from signal contact J2-15 to contact J2-49. Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connector for the solenoid and the ECM connectors remain disconnected.
Remove the jumper wire that was installed in the last test step.
At the J2 connector for the ECM, use a wire removal tool to remove wire J834-PU(Purple) from contact J2-15.
Reconnect the machine harness connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Use a multimeter probe that is not connected to a multimeter or a similar device to make contact with the ECM at contact J2-15 through the empty space in the J2 connector.
Observe the status of the diagnostic code. Ground the other end of the multimeter probe
Cat SIS web machinery list:
Parts pin Caterpillar catalog:
4J5240
PIN
D7E, D7E LGP, D7F, D7G, D7G2, D7H, D7R, D7R II, D7R XR
D7E, D7E LGP, D7F, D7G, D7G2, D7H, D7R, D7R II, D7R XR
3G4929
PIN
D7H, D8L, D8N
D7H, D8L, D8N
6Y6752
PIN
D7E, D7E LGP, D7H, D7R, D7R II, D7R XR
D7E, D7E LGP, D7H, D7R, D7R II, D7R XR
3J6182
PIN ASSEM.
D7F, D7G, D7G2, D7H
D7F, D7G, D7G2, D7H
6Y7474
PIN
D7H, D7R, D7R II, D7R XR
D7H, D7R, D7R II, D7R XR
7T9308
PIN AS-CARTRIDGE
D8R, D9R
D8R, D9R
2663152
PIN AS-CARTRIDGE
D8R, D8R II, D8T, D9R, D9T
D8R, D8R II, D8T, D9R, D9T
1583653
PIN
D8R, D8R II, D8T
D8R, D8R II, D8T
2374872
PIN-PIVOT
D8R, D8R II, D8T
D8R, D8R II, D8T
1620390
PIN
D8R, D8R II, D8T
D8R, D8R II, D8T
2195735
PIN
D8R, D8T
D8R, D8T
2195743
PIN
D8R, D8T
D8R, D8T
2639966
PIN AS
D6R II
D6R II
9P9548
PIN
D10N, D10R, D11N, D11R, D6R II, D8T, D9R
D10N, D10R, D11N, D11R, D6R II, D8T, D9R
9V4908
PIN AS
973, 973C, 973D
973, 973C, 973D
2K9183
PIN-SPRING
561N, 953C, 953D, 963C, 963D, 973C, 973D, D5N, D5R LGP, D6N, D7E, PM-565
561N, 953C, 953D, 963C, 963D, 973C, 973D, D5N, D5R LGP, D6N, D7E, PM-565
1582232
PIN
953C, 953D, 963C, 963D, 973C, 973D
953C, 953D, 963C, 963D, 973C, 973D
1243551
PIN-CLEVIS
953C, 963C, 973C
953C, 963C, 973C
3W7559
PIN AS
953, 953C, 953D
953, 953C, 953D
3171050
PIN
953D
953D
2770559
PIN AS
953D
953D
2770555
PIN AS
953D
953D
7P7428
PIN
943, 953, 953B, 953C, 953D, D6R II, D7R II, D8R II
943, 953, 953B, 953C, 953D, D6R II, D7R II, D8R II
1466315
PIN-ADJUSTMENT
583T, 587R, 587T, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G II, 938H, 950 GC, 950F II, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D3G, D4G, D5G, ...
583T, 587R, 587T, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G II, 938H, 950 GC, 950F II, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D3G, D4G, D5G, ...