AVSPARE.COM
parts catalog

PIPE 0878511 - Caterpillar



0878511 PIPE Caterpillar parts E70B PIPE
Rating:
10
Alternative (cross code) number:
CA0878511
087-8511
0878511
Caterpillar 0878511 PIPE
Weight: 6 pounds 2 kg.

Buy PIPE 0878511 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 0878511:

EXCAVATOR  E70B   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:


Illustration 2 g02585096
Marks for tightening main bearings
Table 1
Specification for 253-9882 Cylinder Block Gp and 273-7595 Cylinder Block Gp
Item Qty Part Specification Description
The top face of the cylinder block, bottom surface of spacer plate (1) and both sides of plate gasket (2) must be free of fuel, oil, water, gasket adhesives, assembly compounds and any other contaminants during assembly.
1 2 225-3100 Spacer Plate Thickness is 8.585 0.025 mm (0.3380 0.0010 inch).
2 2 225-3101 Plate Gasket Thickness of plate gasket that is between cylinder block and spacer plate is 0.208 0.025 mm (0.0082 0.0010 inch).
3 4 7C-9614 Taperlock Plug Before assembly, apply Loctite low breakloose PST on the threads.
Torque to 80 15 N m (60 11 lb ft).
A 4 4N-1650 Dowel Extension of the dowels on the left bank and right bank from the cylinder block is 18.5 0.5 mm (0.73 0.02 inch).
4 7 232-7607 Crankshaft Cap The crankshaft caps must be installed with the identifying marks toward the front of the engine. The number of the main bearing cap must also match the cast number on the left side of each main bearing saddle.
B - - Bore in cylinder block for main bearing is 129.891 0.013 mm (5.1138 0.0005 inch).
C - - The distance from the centerline of the crankshaft bearing bore to the top of the cylinder block is 419.10 0.15 mm (16.500 0.006 inch).
D - - The distance from the centerline of the crankshaft bearing bore to the bottom of the cylinder block is 165.10 0.10 mm (6.500 0.004 inch).
E - - The width of the slot for the crankshaft cap (4) is 236.00 0.05 mm (9.291 0.002 inch).
Width of crankshaft cap (4) is 235.500 0.025 mm (9.2716 0.0010 inch).
5 14 3P-1323 Bearing Cap Bolt Use the following procedure to install the crankshaft cap:
1. Apply clean engine oil on the threads of the bolts (6). Loosely install the bolts (6).
2. Apply clean engine oil on the threads of the side bearing cap bolts (5) and the washers. Loosely install the side bearing cap bolts (5) and the washers.
3. Tighten the bolts (6) first on the main bearing tab side of the crankshaft cap (4) to 258 14 N m (190 10 lb ft).
4. Tighten the bolts (6) that are opposite the main bearing tab side of the crankshaft cap (4) to 258 14 N m (190 10 lb ft).
5. Put a mark on each bolt (6) and each crankshaft cap (4). See Illustration 2.
6. Tighten the bolts (6) that are placed opposite the main bearing tab side of the crankshaft cap (4) from the mark by angle (F) of 120 5 degrees.
7. Tighten the bolts (6) that are placed on the main bearing tab side of the crankshaft cap (4) from the mark by angle (F) of 120 5 degrees.
8. Tighten the side bearing cap bolts

Caterpillar parts catalog:

Caterpillar parts catalog
E70B TRACK-TYPE EXCAVATOR 5TG00001-UP (MACHINE) POWERED BY 4D32 ENGINE


Parts pipe Caterpillar catalog:

0968607 PIPE
307, E110, E70, E70B
0969198 PIPE
307, E70, E70B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.