AVSPARE.COM
parts catalog

PIPE AS-EXHAUST EXTENSION 2881262 - Caterpillar


2881262 PIPE AS-EXHAUST EXTENSION Caterpillar parts C13, TH35-C13T
Rating:
80
Alternative (cross code) number:
CA2881262
288-1262
2881262
Caterpillar 2881262 PIPE AS-EXHAUST EXTENSION

Buy PIPE AS-EXHAUST EXTENSION 2881262 Caterpillar genuine, new aftermarket tractor parts with delivery
PETROLEUM PACKAGE, TRUCK ENGINE,

Compatible equipment models: 2881262:

PETROLEUM PACKAGE  TH35-C13T  
TRUCK ENGINE  C13   Caterpillar
Number on catalog scheme: 2
  For full view, you need register

Information:


Table 1
Required Tools    
Qty     Part Number     Description    
1     9U-5016     Torque Wrench    
1     9U-5017     Torque Wrench    
1     6V-7926     Dial Indicator Group    
Illustration 1 g00728167
Final Drive (1) Wheel hub (2) Roller bearing (3) Gear (support) (4) Steering case (5) Shim (6) Bolt (7) Shim (8) Pinion (9) Washer (friction)
Install wheel hub (1) and associated roller bearings (2) .
Illustration 2 g00731241
Checking the Rolling Torque of the Wheel Hub
Use 9U-5017 Torque Wrench and check the rolling torque of wheel hub (1). The rolling torque should be 25 5 N m (18.44 3.7 lb ft). If the rolling torque is too great, this indicates that the bearings are restricted.
Illustration 3 g00728172
Checking the Gear (Support) with the Dial Indicator
Set a dial indicator to zero onto the surface of gear (support) (3) .
Illustration 4 g00728178
Use the dial indicator which has been set to zero in Step 3 and check the distance between the outer surface of roller bearing (2), and the plane of steering case (4) .
Assemble a shim pack (5) that is equal to the measurement that was taken in Step 4. Install the shim pack and gear (support) (3). Tighten bolts (6) .
Check the rolling torque of wheel hub (1) again with 9U-5016 Torque Wrench. The maximum rolling torque that is allowable is 45 5 N m (33.2 3.7 lb ft).Note: Shims (5) are available in the following thicknesses: 0.15 mm (0.0059 inch), 0.20 mm (0.0079 inch) and 0.50 mm (0.0197 inch). A shim with a thickness of 0.2 mm (0.0079 inch) will change the rolling torque by approximately 10 N m (7.3756 lb ft).
When the wheel bearing adjustment is correct, remove bolts (6) in order to prepare for final installation. If the bolts that are used are bright, coat the bolt with anti-seize grease before applying 9S-3263 Thread Lock Compound to the threads of the bolt. If the bolts that are used are plated, apply 9S-3263 Thread Lock Compound to the threads of the bolts only.
Install bolts (6). Tighten the bolts to a torque setting of 285 15 N m (210 11 lb ft) if the bolts are plated. Tighten the bolts to a torque setting of 315 15 N m (232 11 lb ft) if the bolts are bright.
Install shim (7) between pinion (8) and washer (9) in order to give a pinion end play of 0.4 0.1 mm (0.0157 0.0039 inch).Note: Shims (7) are available in the following thicknesses: 0.10 mm (0.0039 inch), 0.20 mm (0.0079 inch), 0.30 mm (0.0118 inch) and 0.50 mm (0.0197 inch).

Caterpillar parts catalog:

Caterpillar parts catalog
C13 On-Highway Engine LEE00001-UP
TH35-C13I Petroleum Package LEE00001-UP POWERED BY C13 Engine


Parts pipe Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.