AVSPARE.COM
parts catalog

PIPE A. 2H9566 - Caterpillar



2H9566 PIPE A. Caterpillar parts PIPE
Rating:
11
Alternative (cross code) number:
CA2H9566
2H-9566
2H9566
Caterpillar 2H9566 PIPE A.
Weight: 0.01 pounds 0 kg.

Buy PIPE A. 2H9566 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01283744
Schematic for the Auxiliary 2 Solenoid CircuitThis diagnostic code is associated with the Auxiliary 2 Solenoid. This diagnostic code is recorded when the ECM detects a short to the +battery in the electrical path. The electrical path goes from the ECM to the solenoid and back to the ECM. The return circuit is connected for all solenoids. The return circuit connects to contact J1-60 (wire H802-GY) of the Machine ECM.The possible causes of this diagnostic code are listed:
The signal circuit from the ECM to the solenoid valve is shorted to the +battery.
The return circuit from the solenoid valve is shorted to the +battery.
The ECM has failed. This is unlikely.Note: Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code is corrected. Note: Ensure that the diagnostic code is active and that the diagnostic code indicator is active.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT
Disconnect the negative battery cable and turn the key start switch to the OFF position.
Disconnect the machine harness connector from the solenoid. Disconnect the machine harness connectors J1 and J2 from the ECM.
At the machine harness ECM connectors, measure the resistance from contact J1-61 (wire P979-YL) to all of the other contacts that are used in the J1 and J2 connectors for the ECM.Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
YES - Each resistance measurement is greater than 5000 ohms. The resistance measurement does not indicate a short in the machine harness. Proceed to Test Step 2.
NO - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. Repair: The short is between wire P979-YL and the circuit that has a low resistance measurement.For information on testing for short circuits and finding short circuits, refer to Testing and Adjusting, "Wiring Harness (Short Circuit) - Test". Repair the machine harness or replace machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECMThe key start switch remains in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the machine harness connector J2 for the ECM, use a 151-6320 Removal Tool to remove the solenoid energize wire P979-YL and socket at contact J1-61 from the harness connector.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Reconnect the negative battery cable and turn the key start switch to the ON position.
Observe the status of the active CID 2212 FMI 03 diagnostic code.Expected Result:The CID 2212 FMI 03 diagnostic code is no longer active. A CID 2212 FMI


Parts pipe Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.