5I8044 PIPE Caterpillar parts
320B, 320C, 320C FM
Rating:
Alternative (cross code) number:
CA5I8044
5I-8044
5I8044
CA5I8044
5I-8044
5I8044
Weight: 0.43 pounds 0 kg.
EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 5I8044 Air Inlet/Exhaust Pipe for Models 320B/320C/320C FM
CTP For Models 320B/320C/320C FM || Highly Efficient || Easy in-and-out fit
CTP For Models 320B/320C/320C FM || Highly Efficient || Easy in-and-out fit
CTP 5I8044 Air Inlet/Exhaust Pipe for Models 320B/320C/320C FM
CTP For Models 320B/320C/320C FM || Highly Efficient || Easy in-and-out fit
CTP For Models 320B/320C/320C FM || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
9
For full view, you need register
Information:
Two-Piece Articulated Piston
Illustration 1 g00293184
Illustration 2 g01093113 (1) Crown assembly (2) Connecting rod Note: Install the rod and piston group in the engine with the part number of the forging for the rod assembly to the rear of the engine. The rear of the engine is the flywheel end of the engine. Lubricate the rod and piston group with clean engine oil before you insert the rod and piston group into the block.Top Ring and Intermediate Ring
(3) The top ring has the mark "UP-1". Install the piston ring with the side marked "UP-1" toward the top of the piston. The colored stripe faces to the right of the ring end gap.Piston ring end gap ... 0.40 0.10 mm ( 0.016 0.004 inch)Thickness of new top piston ring ... 3.453 mm (0.1359 inch) (4) The intermediate ring has the mark "UP-2". Install the piston ring with the side marked "UP-2" toward the top of the piston. The colored stripe faces to the right of the piston ring end gap.Piston ring end gap ... 1.50 0.10 mm (0.060 0.004 inch)Width of groove in new piston for intermediate piston ring ... 3.06 0.01 mm (0.121 0.001 inch)Thickness of new intermediate piston ring ... 2.98 0.01 mm (0.117 0.0004 inch)Oil Control Ring
(5) The oil control piston ring has a spring that is installed with the ring. The gap in the spring should be a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The colored portion can be to the right or to the left of the ring end gap. Piston ring end gap ... 0.45 0.15 mm (0.018 0.006 inch)Width of groove in new piston for oil control piston ring ... 4.03 0.01 mm (0.159 0.001 inch)Thickness of new oil control piston ring ... 3.98 0.01 mm (0.157 0.001 inch)After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 degrees from each other. (6) Piston skirt Lubricate the entire piston in zone (A) prior to assembly into the cylinder block. Use clean engine oil.Piston Pin
(7) Piston pin Piston pin diameter ... 46.000 0.005 mm (1.8110 0.0002 inch)Length of piston pin ... 91.50 0.15 mm (3.602 0.006 inch)Thoroughly lubricate the piston pin with clean engine oil prior to assembly.
Illustration 1 g00293184
Illustration 2 g01093113 (1) Crown assembly (2) Connecting rod Note: Install the rod and piston group in the engine with the part number of the forging for the rod assembly to the rear of the engine. The rear of the engine is the flywheel end of the engine. Lubricate the rod and piston group with clean engine oil before you insert the rod and piston group into the block.Top Ring and Intermediate Ring
(3) The top ring has the mark "UP-1". Install the piston ring with the side marked "UP-1" toward the top of the piston. The colored stripe faces to the right of the ring end gap.Piston ring end gap ... 0.40 0.10 mm ( 0.016 0.004 inch)Thickness of new top piston ring ... 3.453 mm (0.1359 inch) (4) The intermediate ring has the mark "UP-2". Install the piston ring with the side marked "UP-2" toward the top of the piston. The colored stripe faces to the right of the piston ring end gap.Piston ring end gap ... 1.50 0.10 mm (0.060 0.004 inch)Width of groove in new piston for intermediate piston ring ... 3.06 0.01 mm (0.121 0.001 inch)Thickness of new intermediate piston ring ... 2.98 0.01 mm (0.117 0.0004 inch)Oil Control Ring
(5) The oil control piston ring has a spring that is installed with the ring. The gap in the spring should be a distance of 180 degrees from the ring end gap when the oil control piston ring is assembled. The colored portion can be to the right or to the left of the ring end gap. Piston ring end gap ... 0.45 0.15 mm (0.018 0.006 inch)Width of groove in new piston for oil control piston ring ... 4.03 0.01 mm (0.159 0.001 inch)Thickness of new oil control piston ring ... 3.98 0.01 mm (0.157 0.001 inch)After the piston rings have been installed, rotate the piston rings so that the end gaps are 120 degrees from each other. (6) Piston skirt Lubricate the entire piston in zone (A) prior to assembly into the cylinder block. Use clean engine oil.Piston Pin
(7) Piston pin Piston pin diameter ... 46.000 0.005 mm (1.8110 0.0002 inch)Length of piston pin ... 91.50 0.15 mm (3.602 0.006 inch)Thoroughly lubricate the piston pin with clean engine oil prior to assembly.
Caterpillar parts catalog:
Parts pipe Caterpillar catalog:
320 L, 320B, 320B L, 320N
320 L, 320B, 320B L, 320N
320 L, 320B, 320B L, 320N
320 L, 320B, 320B L, 320N
320B, 320C, 323D LN, 323D SA, 323E L, 325B, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, OEMS
320B, 320C, 320C FM
320B, 320C, 320C FM
320B, 320C, 320C FM
320B, 320C, 320C FM
320C, 320C FM
320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
320B
5I8043
PIPE
320B, 320C, 320C FM
320B, 320C, 320C FM
1719072
PIPE AS
320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
1932776
PIPE AS
320C
320C
1932777
PIPE AS
320C
320C
1614714
PIPE
574
574
1654408
PIPE
574
574
1786583
PIPE
320C
320C
320C, 320C FM
320B, 320C, 320C FM
320B, 320C, 320C FM
320B, 320C, 320C FM
320B, 320C, 320C FM