1475836 PISTON Caterpillar parts
315, 315B, 315B L, 315C, 317B LN, 318B
Rating:
Alternative (cross code) number:
CA1475836
147-5836
1475836
CA1475836
147-5836
1475836
Weight: 7 pounds 3 kg.
EXCAVATOR,
Number on catalog scheme:
10
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure.
Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to appropriate lifters (1).
Illustration 1 g01340518
Use Tooling (B) in order to remove lifters (1). Note: Place a temporary identification mark on each lifter in order to identify the correct location.
Repeat Step 1 and Step 2 in order to remove the remaining lifters. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
It is strongly recommended that all lifters should be replaced when a new camshaft is installed.
Clean the lifters. Follow Step 1.a through Step 1.c in order to inspect the lifters. Replace any worn lifters or damaged lifters.
Inspect the seat of the pushrod in the lifter for visual wear or damage.
Inspect the shank of the lifter for wear or damage. Refer to Specifications, "Lifter Group" for more information.
Inspect the face of the lifter that runs on the camshaft for visual wear or damage.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft to access to the cylinder block in order to install appropriate lifters (1).
Lubricate lifters (1) with clean engine oil.
Illustration 2 g01340518
Use Tooling (B) to install lifters (1) to the cylinder block. Ensure that used lifters are installed in the correct location. Note: The lifters should be free to rotate.
Repeat Step 1 and Step 4 in order to install the remaining lifters. End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.
Table 1
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Start By:
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the correct procedure.
Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure. Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft in order to gain access to appropriate lifters (1).
Illustration 1 g01340518
Use Tooling (B) in order to remove lifters (1). Note: Place a temporary identification mark on each lifter in order to identify the correct location.
Repeat Step 1 and Step 2 in order to remove the remaining lifters. Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
(1)A 9U-6198 Crankshaft Turning Too 1
(2)A 9U-7336 Housing As 1
5P-7305 Engine Turning Tool 1
B 1U-7262 Telescopic Magnet 1
(1) The Crankshaft Turning Tool is used on the front pulley.
(2) This Tool is used in the aperture for the electric starting motor.Note: Either Tooling (A) can be used. Use the Tooling that is most suitable.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
It is strongly recommended that all lifters should be replaced when a new camshaft is installed.
Clean the lifters. Follow Step 1.a through Step 1.c in order to inspect the lifters. Replace any worn lifters or damaged lifters.
Inspect the seat of the pushrod in the lifter for visual wear or damage.
Inspect the shank of the lifter for wear or damage. Refer to Specifications, "Lifter Group" for more information.
Inspect the face of the lifter that runs on the camshaft for visual wear or damage.
If the crankshaft is installed, use Tooling (A) to rotate the crankshaft to access to the cylinder block in order to install appropriate lifters (1).
Lubricate lifters (1) with clean engine oil.
Illustration 2 g01340518
Use Tooling (B) to install lifters (1) to the cylinder block. Ensure that used lifters are installed in the correct location. Note: The lifters should be free to rotate.
Repeat Step 1 and Step 4 in order to install the remaining lifters. End By:
Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install" for the correct procedure.
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the correct procedure.
Caterpillar parts catalog:
Parts piston Caterpillar catalog:
311, 311B, 312, 315, 317, 320 L, OEMS
312B, 313D2 LGP, 315B, 315B L, 315C, 315D L, 316E L, 318D L, 318D2 L, OEMS
317B LN, 318B
315B FM L, 317B LN, 318B, 320B, OEMS
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
311B, 312B, 315B, 315B FM L, 318B
303, 303.5C, 303C CR, 304, 304C CR, 305, 305.5, 305.5E, 305C CR, 306, 306E, 307B, 307C, 308C, 311B, 311C, 312B, 312C, 312C L, 313B, 314C, 315C, 318B, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D LRR,...
318B, 318C, 320, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320N, 321C, 322C
311C, 311D LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 315C, 315D L, 318D L, 318D2 L
315, 315B, 939, 939C, D5C III
315, 315B, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
315, 315B, 933, 933C, 939, 939C, D3C III, D4C III, D5C III
1588924
PISTON
315B, 315B L, 315C, 315D L, 317B LN, 318B
315B, 315B L, 315C, 315D L, 317B LN, 318B
1336687
PISTON
315B L, 317B LN
315B L, 317B LN
1475818
PISTON
315, 315B, 315B L, 315C, 315D L, 316E L, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, M313C, M313D, M318C, M318C MH, M318D, M318D MH
315, 315B, 315B L, 315C, 315D L, 316E L, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, M313C, M313D, M318C, M318C MH, M318D, M318D MH
312B, 313D2 LGP, 315B, 315B L, 315C, 315D L, 316E L, 318D L, 318D2 L, OEMS
312B, 312B L, 312C, 312C L, 313B, 314C, 345B II, 345C
1438023
PISTON
311B, 311C, 312B, 312B L, 312C, 312C L, 313B, 314C, 315, 320B, 320C, 320D, 322C, 323D L, 324D, 324D L, 325C, 325C L, 325D, 325D L, 329D L, 330B L, 330C, 330C L, M315C, M315D, M316C, M316D
311B, 311C, 312B, 312B L, 312C, 312C L, 313B, 314C, 315, 320B, 320C, 320D, 322C, 323D L, 324D, 324D L, 325C, 325C L, 325D, 325D L, 329D L, 330B L, 330C, 330C L, M315C, M315D, M316C, M316D
2127962
PISTON
318B
318B
1475851
PISTON
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK711, TK721, TK722, TK732, TK741, T...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 318B, 318C, 319C, 319D, 319D L, 319D LN, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, TK711, TK721, TK722, TK732, TK741, T...
315B FM L, 317B LN, 318B, 320B, OEMS
0862138
PISTON
307, 307B, 308C, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
307, 307B, 308C, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
317B LN, 318B
1847656
PISTON
311D LRR, 312B L, 312C, 312D, 312E, 314D LCR, 314E LCR, 315B L, 315C, 315D L, 316E L, 317B LN, 318E L
311D LRR, 312B L, 312C, 312D, 312E, 314D LCR, 314E LCR, 315B L, 315C, 315D L, 316E L, 317B LN, 318E L