1956595 PISTON & ROD GP Caterpillar parts
C-12
Rating:
Alternative (cross code) number:
CA1956595
195-6595
1956595
CA1956595
195-6595
1956595
TRUCK ENGINE,
Compatible equipment models: 1956595:
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4089 Hydraulic Platform Jack 1
4C-4090 Handling Tool Gp 1 Start By:
Remove the wheel. Refer to Disassembly and Assembly, "Wheel (Final Drive) - Remove and Install".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, all hoses, and all tubes.
Drain the oil from the hydraulic tank. Refer to Operation and Maintenance Manual, "Hydraulic Oil and Filters - Change" for the correct procedure.
Illustration 1 g02476051
Remove the bolts and covers (1).
Illustration 2 g02476064
Remove clamps (3) and disconnect hose assemblies (2) and hose assemblies (5).
Disconnect harness assembly (4).
Illustration 3 g01059136
Remove the bolts and shield (6) from planetary (7). Note: Put orientation and location marks on the planetary and on the frame for installation purposes.
Use Tooling (A) and support planetary (7). Remove bolts (8). Use Tooling (A) and remove planetary (7) and the propel motor from the machine. The weight of the planetary and the propel motor is approximately 310 kg (685 lb).
Table 1
Required Tools
Tool Part Number Part Description Qty
A 4C-4089 Hydraulic Platform Jack 1
4C-4090 Handling Tool Gp 1 Start By:
Remove the wheel. Refer to Disassembly and Assembly, "Wheel (Final Drive) - Remove and Install".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, all hoses, and all tubes.
Drain the oil from the hydraulic tank. Refer to Operation and Maintenance Manual, "Hydraulic Oil and Filters - Change" for the correct procedure.
Illustration 1 g02476051
Remove the bolts and covers (1).
Illustration 2 g02476064
Remove clamps (3) and disconnect hose assemblies (2) and hose assemblies (5).
Disconnect harness assembly (4).
Illustration 3 g01059136
Remove the bolts and shield (6) from planetary (7). Note: Put orientation and location marks on the planetary and on the frame for installation purposes.
Use Tooling (A) and support planetary (7). Remove bolts (8). Use Tooling (A) and remove planetary (7) and the propel motor from the machine. The weight of the planetary and the propel motor is approximately 310 kg (685 lb).
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts piston Caterpillar catalog:
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14G, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 1673C, 1...
3116, 3126, 3126B, 3126E, 3176, 3176B, 3176C, 3196, 3304, 3306, 3306B, 3306C, 3406B, 3406C, 3406E, 3456, 3516B, 651B, 776C, 776D, 777, 777B, 777C, 777D, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 7...
3176, 3176B, 3176C, 3196, C-10, C-12
3176, 3176B, 3176C, 3196, C-10, C-12
3176, 3176B, 3176C, 3196, C-10, C-12
1172673
PISTON & ROD GP
3196, 85D, 85E, 95E, C-12
3196, 85D, 85E, 95E, C-12
2735799
PISTON & ROD GP
3406E, C15
3406E, C15
1308841
PISTON & ROD GP
3406E
3406E
1568265
PISTON & ROD GP
3412E
3412E
1470617
PISTON & ROD GP
3508B, 3512B, 3516B
3508B, 3512B, 3516B
1333360
PISTON & ROD GP
3406E, C-15
3406E, C-15