2167386 PISTON Caterpillar parts
315C, 315D L, D3G, D4G, D5G
Rating:
Alternative (cross code) number:
CA2167386
216-7386
2167386
CA2167386
216-7386
2167386
Weight: 2 pounds 1 kg.
Information:
PISTON DIAMETER
28.59
mm
THICKNESS
63
mm
NUMBER OF C BORE
0
Wear Ring Dia
63.27
EXCAVATOR, TRACK-TYPE TRACTOR,
Compatible equipment models: 2167386:
Number on catalog scheme:
1
For full view, you need register
Information:
Before failure:
SMCS CODE DESCRIPTION SC MC CV CO
1119-037-BC Replace Bolts 0.5 0.5 0.5 0.5
1105-025-ES-S Adjust Lash settings 1.5 1.5 1.5 1.5PARTS DISPOSITION
Handle the parts in accordance with your WarrantyBulletin on warranty parts handling.Attach. (1-Rework Procedure)Rework ProcedureDifferent procedures are needed for enginesequipped with Pac brakes versus engines equipped with Jacobs brakes. Thenew bolts used for Jacobs brakes will not fit on Pac brakes. Identify whichtype of compression brake is on the engine and follow the appropriate procedure.Pac Brake Only:Before failure: This procedure should be usedwhen the valve covers need to be removed for any reason, such as normalmaintenance. It should only be applied once per engine. It should onlybe applied on engines equipped with Pac brakes.
Torque each of the four brake mounting bolts oneach brake to 150N-m.
Torque the nut on each brake mounting stud to140N-m
Continue with normal maintenance procedures
After Failure: This procedure should be usedafter the failure of an exhaust rocker arm.
Replace all 6 exhaust rocker arms with 10R1364arms per normal procedure as specified in the service manual.
Replace the intake rocker arm for the cylinderwith the broken exhaust arm only.
Torque all four of the brake bolts on each braketo 150 N-m.
Torque the nut on each brake mounting stud to140N-m
Replace the air intake temperature sensor.
Set the slave lash to the proper setting calledout in SISweb.
Jake Brake only:Before failure: This procedure shouldbe used when the valve covers need to be removed for any reason, such asnormal maintenance. It should only be applied once per engine. It shouldonly be applied on engines equipped with Jacobs compression brakes.There are 4 bolts on each brake. Three of themneed to be replaced by new 257-2122 bolts. The bolt across from the studshould not be replaced. The current washers can be reused.
Inspect to see if bolts have already been replaced.The new bolts (shown in figure 1) have a hex head; the original bolts are12-point.
Loosen the brake fasteners enough that bolts 1-3can be removed.
Remove bolts 1-3 and replace them with 257-2122bolts. Torque the bolts to 50N-m plus a 90-degree turn.
Failure to replace the correct boltsmay cause loss of brake performance.
Torque Bolt number 4 to 160 N-m DO NOT REPLACETHIS BOLT
Torque the nut on the mounting stud to 140N-m.
Adjust lash settings to the proper value calledout in SIS.
Repeat for each brake.
After Failure: This procedure should beused after the failure of an exhaust rocker arm.
Replace all 6 exhaust rocker arms with 10R1364arms per normal procedure as specified in the service manual.
Replace the intake rocker arm for the cylinderwith the broken exhaust arm only.
Replace three of the compression brake bolts oneach brake with new 257-2122 bolts. The bolt opposite the stud must remainthe current bolt. Consult figure 1 to determine which bolts to replace.Reuse the current washer.
It is very important to locate thebolts in the correct holes. Failure to do so may cause loss of brake performance.
Torque all bolts to 50 nm plus a 90 degree turn.
Torque the nut on the mounting stud to 140N-m
Replace the air intake temperature sensor.
Set the slave lash to the proper setting calledout in SISweb
SMCS CODE DESCRIPTION SC MC CV CO
1119-037-BC Replace Bolts 0.5 0.5 0.5 0.5
1105-025-ES-S Adjust Lash settings 1.5 1.5 1.5 1.5PARTS DISPOSITION
Handle the parts in accordance with your WarrantyBulletin on warranty parts handling.Attach. (1-Rework Procedure)Rework ProcedureDifferent procedures are needed for enginesequipped with Pac brakes versus engines equipped with Jacobs brakes. Thenew bolts used for Jacobs brakes will not fit on Pac brakes. Identify whichtype of compression brake is on the engine and follow the appropriate procedure.Pac Brake Only:Before failure: This procedure should be usedwhen the valve covers need to be removed for any reason, such as normalmaintenance. It should only be applied once per engine. It should onlybe applied on engines equipped with Pac brakes.
Torque each of the four brake mounting bolts oneach brake to 150N-m.
Torque the nut on each brake mounting stud to140N-m
Continue with normal maintenance procedures
After Failure: This procedure should be usedafter the failure of an exhaust rocker arm.
Replace all 6 exhaust rocker arms with 10R1364arms per normal procedure as specified in the service manual.
Replace the intake rocker arm for the cylinderwith the broken exhaust arm only.
Torque all four of the brake bolts on each braketo 150 N-m.
Torque the nut on each brake mounting stud to140N-m
Replace the air intake temperature sensor.
Set the slave lash to the proper setting calledout in SISweb.
Jake Brake only:Before failure: This procedure shouldbe used when the valve covers need to be removed for any reason, such asnormal maintenance. It should only be applied once per engine. It shouldonly be applied on engines equipped with Jacobs compression brakes.There are 4 bolts on each brake. Three of themneed to be replaced by new 257-2122 bolts. The bolt across from the studshould not be replaced. The current washers can be reused.
Inspect to see if bolts have already been replaced.The new bolts (shown in figure 1) have a hex head; the original bolts are12-point.
Loosen the brake fasteners enough that bolts 1-3can be removed.
Remove bolts 1-3 and replace them with 257-2122bolts. Torque the bolts to 50N-m plus a 90-degree turn.
Failure to replace the correct boltsmay cause loss of brake performance.
Torque Bolt number 4 to 160 N-m DO NOT REPLACETHIS BOLT
Torque the nut on the mounting stud to 140N-m.
Adjust lash settings to the proper value calledout in SIS.
Repeat for each brake.
After Failure: This procedure should beused after the failure of an exhaust rocker arm.
Replace all 6 exhaust rocker arms with 10R1364arms per normal procedure as specified in the service manual.
Replace the intake rocker arm for the cylinderwith the broken exhaust arm only.
Replace three of the compression brake bolts oneach brake with new 257-2122 bolts. The bolt opposite the stud must remainthe current bolt. Consult figure 1 to determine which bolts to replace.Reuse the current washer.
It is very important to locate thebolts in the correct holes. Failure to do so may cause loss of brake performance.
Torque all bolts to 50 nm plus a 90 degree turn.
Torque the nut on the mounting stud to 140N-m
Replace the air intake temperature sensor.
Set the slave lash to the proper setting calledout in SISweb
Caterpillar parts catalog:
Parts piston Caterpillar catalog:
910G, 933C, C11, C13, C15, C18, C9, C9.3, CB-534D, CD-54, CX31-C13I, CX31-C15I, CX31-C18I, CX31-C9I, CX35-C18I, CX35-P800, D3C III, D3K XL, D4G, D5G, D5K LGP, D5K2 XL, D6N, D6T, D6T LGP, D6T LGPPAT, D...
312B, 313D2 LGP, 315B, 315B L, 315C, 315D L, 316E L, 318D L, 318D2 L, OEMS
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
315C, 315D L, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 3...
315D L, 316E L, 318C, 318D L, 318E L, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 3...
315C, D3G, D4G, D5G
315, 315B, 939C, D5C III, D5G
933, 933C, D3C III, D3G, D4C III, D4G, D5G
1143593
PISTON
933C, D3C III, D3G
933C, D3C III, D3G
1143592
PISTON
939C, D4C III, D4G, D5C III, D5G
939C, D4C III, D4G, D5C III, D5G
2118217
PISTON
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D6K LGP
D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D6K LGP
1720307
PISTON AS
515, 525, 525B, 525C, 535B, 535C, 545, 545C, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D6K LGP
515, 525, 525B, 525C, 535B, 535C, 545, 545C, D3G, D3K XL, D3K2 LGP, D4G, D4K XL, D4K2 XL, D5G, D5K LGP, D5K2 XL, D6K LGP
6C8556
PISTON
318B, 320 L, 320B, 325B L, 330B L, 345B L
318B, 320 L, 320B, 325B L, 330B L, 345B L
5W7522
PISTON
205
205
5W7490
PISTON
205
205
8U3275
PISTON
205
205
8U3276
PISTON
205
205
8U0773
PISTON
212
212
0961184
PISTON
311, 320 L, 320B, E110, E110B, E120B, E200B, E450
311, 320 L, 320B, E110, E110B, E120B, E200B, E450
1195293
PISTON
311B
311B
311, 311B, 312B, 320 L, 320B
311, 311B, 312B, 320 L, 320B
311, 311B, 312B, 320 L, 320B
120G, 12G, 130G, 14G, 315C, 315D L, 3P, 3S, 627B, 637D, 657B, 657E, 910, 931B, 933, 939, D3B, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL, D5C III, D5G, D5K LGP, D5K2 XL