AVSPARE.COM
parts catalog

PISTON-CYL 2389345 - Caterpillar



2389345 PISTON-CYL Caterpillar parts PISTON
Rating:
46
Alternative (cross code) number:
CA2389345
238-9345
2389345
Caterpillar 2389345 PISTON-CYL
Weight: 6 pounds 2 kg.

Buy PISTON-CYL 2389345 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.
There are two types of engine oil cooler that can be installed on this engine.Engine Oil Cooler with a Low Mounted Filter Base
Illustration 1 g01332170
Typical example
(1) Oil cooler
(2) Long setscrew
(3) Short setscrew
(4) Joint
(5) Setscrews
(6) Housing for the oil cooler
(7) Joint Perform the following procedure in order to inspect the engine oil cooler with the low mounted filter:
Place a container under the oil cooler in order to collect any engine oil or coolant that drains from the oil cooler.
Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove" for removal of the engine oil cooler.
Thoroughly clean the oil cooler (1) and the cylinder block.
Personal injury can result from air pressure.Personal injury can result without following proper procedure. When using pressure air, wear a protective face shield and protective clothing.Maximum air pressure at the nozzle must be less than 205 kPa (30 psi) for cleaning purposes.
Inspect the oil cooler (1) for cracks and dents. Replace the oil cooler (1) if cracks or dents exist. Ensure that no restrictions for the flow of lubricating oil exist in the oil cooler (1). Dry the oil cooler (1) with low pressure air. Flush the inside of the oil cooler (1) with clean lubricating oil.
Refer to Disassembly and Assembly, "Engine Oil Cooler - Install" for installation of the engine oil cooler.
Ensure that the cooling system of the engine is filled to the correct level. Operate the engine. Note: Refer to Operation And Maintenance Manual, "Refill Capacities" for additional information.Check for oil or coolant leakage.Engine Oil Cooler with a High Mounted Filter Base
Illustration 2 g01322246
Typical example
(1) Oil cooler
(2) Joint
(3) Housing for the oil cooler
(4) Nut
(5) Long setscrew
(6) Setscrew
(7) Joint Perform the following procedure in order to inspect the engine oil cooler with the low mounted filter:
Place a container under the oil cooler in order to collect any engine oil or coolant that drains from the oil cooler.
Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove" for removal of the engine oil cooler.
Thoroughly clean the oil cooler (1) and the cylinder block.
Personal injury can result from air pressure.Personal injury can result without following proper procedure. When using pressure air, wear a protective face shield and protective clothing.Maximum air pressure at the nozzle must be less than 205 kPa (30 psi) for cleaning purposes.
Inspect the oil cooler (1) for cracks and dents. Replace the oil cooler (1) if cracks or dents exist. Ensure that no restrictions for the flow of lubricating oil exist in the oil cooler (1). Dry the oil cooler (1) with low pressure air. Flush the inside of the oil cooler (1) with clean lubricating oil.
Refer to Disassembly and Assembly, "Engine Oil Cooler - Install" for installation of the engine oil cooler.
Ensure that the cooling system of the engine is filled to the correct level. Operate the engine. Note: Refer to Operation And Maintenance Manual, "Refill Capacities" for additional information.Check for oil or coolant leakage.


Parts piston Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.