AVSPARE.COM
parts catalog

PISTON 2444876 - Caterpillar


2444876 PISTON Caterpillar parts
Rating:
61
Alternative (cross code) number:
CA2444876
244-4876
2444876
Caterpillar 2444876 PISTON
Weight: 0.26 pounds 0 kg.

Buy PISTON 2444876 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 12 g02518038
(W1) 5 mm (0.197 inch) all around fillet weld (W2) 5 mm (0.197 inch) fillet weld (two sides) (1) Block (fabricated) (2) 9R-1733 Boss (3) 9R-2613 Weld Boss
Weld block (1), boss (2), and two bosses (3) to the support assembly.
Illustration 13 g02517536
(A) Bracket assembly
After the welding is complete, remove bracket assembly (A). Grind the area smooth. Repaint the areas that require paint.
Illustration 14 g02517538
(4) 366-5748 Hose As (5) 228-7092 O-Ring Seal
Use two O-ring seals (5) and the hardware that was removed in Step 2 of the ""Removal Procedure for the 793D"" Section to install hose assembly (4) .
Illustration 15 g02519419
(6) 365-8834 Hose As (7) 2H-6338 O-Ring Seal (8) 365-8835 Tube As
Use two O-ring seals (7) and the hardware that was removed in Step 2 of the ""Removal Procedure for the 793D"" Section to install hose assembly (6) and tube assembly (8) . (M) Approximate space between the flange for tube assembly (8) and the clamp ... 10 mm (0.394 inch)
Illustration 16 g02519516
(8) 365-8835 Tube As (9) 366-7574 Sensor Harness As (10) 5P-9297 Clip (11) 130-5300 Clip (12) 8T-4137 Bolt (13) 8T-4121 Hard Washer'
Use four clips (10), two clips (11), two bolts (12), two washers (13) and the existing hardware in order to secure harness assembly (9) to the machine.
Connect the temperature assembly that was disconnected in Step 2 of the ""Removal Procedure for the 793D"" Section to harness assembly (9) and tube assembly (8) .Note: Tighten the temperature sensor assembly to a torque of 20 3 N m (177 26 lb in).
Illustration 17 g02519636
(N) Hose assemblies (P) Bolt (2) 9R-1733 Boss (14) 7Y-3283 Spacer
Secure hose assemblies (N) for the power train cooler lines group to boss (2) by using bolt (P), spacer (14), and the hardware that was removed in Step 1 of the ""Removal Procedure for the 793D"" Section.Register the Retrofit
Because retrofits to a prime product will change the configuration of the product, updating the configuration in SIMSi and AIMS is important. If the retrofit information is not provided, Caterpillar will not be able to provide important product updates.The following information includes instructions on registering the updates and retrofits.
When performing a retrofit installation, record the vital information in Table 7. Note: If the procedure is performed by the customer, ask the customer to record the proper information.
Table 7
Repair Date        
Product Serial Number        
Service Hours or Service Meter Units        
Removed Component Part Number (1)        
Removed Component Serial Number (1)        
Installed Component Part Number (2)        
Installed Component Serial Number (3)        
( 1 ) Only applies if a component is replaced by a retrofit component. If the product is an engine, and the product retrofit is a kit for upgrading the engine, disregard the "Removed Component" information. Refer to detailed instructions in Step 3 for more


Parts piston Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.