2956092 PISTON Caterpillar parts
420E, 430E
Rating:
Alternative (cross code) number:
CA2956092
295-6092
2956092
CA2956092
295-6092
2956092
Weight: 2 pounds 1 kg.
BACKHOE LOADER,
Number on catalog scheme:
6
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil on the upper main bearing. Do not put engine oil on the back side of the bearing surfaces. Install the upper main bearing in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01184978
Put clean engine oil on the journals of the crankshaft bearing. Attach a suitable lifting device to crankshaft (1). The weight of crankshaft (1) is approximately 60 kg (132 lb). Carefully install the crankshaft in the cylinder block.
Clean the bearing surface of the main bearing caps. Install the lower main bearing in the crankshaft main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing. Do not put engine oil on the back side of the bearing surfaces.
Install crankshaft main bearing caps with the part numbers toward the right hand side of the cylinder block. The numbers should start at the front of the engine. Place clean engine oil or Molylube on the bolt threads and the washers.
Illustration 2 g01028042
Install the bolts for main bearing caps (2). Tighten the bolts to a torque of 54 7 N m (40 5 lb ft).
Turn the bolts for an additional 90 5 degrees (1/4 turn).
Install connecting rod caps (3). Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Check the end play of crankshaft (1) with Tooling (A). The end play must be 0.07 to 0.32 mm (0.003 to 0.013 inch). End By:
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-5096 Dial Indicator Group 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Note: The number six main bearing is the thrust bearing.
Clean the bearing surfaces in the cylinder block for the main bearings. Apply clean engine oil on the upper main bearing. Do not put engine oil on the back side of the bearing surfaces. Install the upper main bearing in the cylinder block. Ensure that the tab on the back side of the bearing engages with the groove in the cylinder block.
Illustration 1 g01184978
Put clean engine oil on the journals of the crankshaft bearing. Attach a suitable lifting device to crankshaft (1). The weight of crankshaft (1) is approximately 60 kg (132 lb). Carefully install the crankshaft in the cylinder block.
Clean the bearing surface of the main bearing caps. Install the lower main bearing in the crankshaft main bearing caps. Ensure that the tab on the back side of the bearing engages with the groove in the main bearing cap. Apply clean engine oil on the lower main bearing. Do not put engine oil on the back side of the bearing surfaces.
Install crankshaft main bearing caps with the part numbers toward the right hand side of the cylinder block. The numbers should start at the front of the engine. Place clean engine oil or Molylube on the bolt threads and the washers.
Illustration 2 g01028042
Install the bolts for main bearing caps (2). Tighten the bolts to a torque of 54 7 N m (40 5 lb ft).
Turn the bolts for an additional 90 5 degrees (1/4 turn).
Install connecting rod caps (3). Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Check the end play of crankshaft (1) with Tooling (A). The end play must be 0.07 to 0.32 mm (0.003 to 0.013 inch). End By:
Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Caterpillar parts catalog:
Parts piston Caterpillar catalog:
416B, 416C, 416D, 420D, 420E, 424D, 426C, 428B, 428C, 428D, 430D, 430E, 432D, 436C, 438B, 438C, 438D, 442D, 446B, 446D
416B, 416C, 416D, 420D, 420E, 424D, 426B, 426C, 428B, 428C, 428D, 430E, 432D, 432E, 434E, 436C, 438C, 438D, 442D, 442E, 444E, 450E, 69D, 725, 730, 773D, 773E
414E, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430D, 430E, 432D, 434E, 436C, 438C, 438D, 442D, 444E
416C, 416D, 420D, 420E, 420F, 424D, 426C, 428C, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 436C, 438C, 438D, 442D, 442E, 444E, 444F, 446B, 446D, 450E, 450F
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315C, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 4...
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, 450E, 450F, TH220B, TH330B, TH340B, TH350B, TH355B, TH460B, TH560B, TH580B
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
416D, 416E, 420D, 420E, 430D, 430E
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 450E, 527
416E, 416F, 420E, 420F
2739413
PISTON
420E, 432E, 434E
420E, 432E, 434E
420E, 420F, 432E, 434E
2949811
PISTON
420D, 420E, 428F, 430D, 430E, 432F, 434F, 444F, 450E
420D, 420E, 428F, 430D, 430E, 432F, 434F, 444F, 450E
420D, 420E, 428F, 430D, 430E, 432F, 434F, 444F, 450E
2764170
PISTON
307D, 308D, 308E, 308E2 CR, 416D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F, 450E, 450F
307D, 308D, 308E, 308E2 CR, 416D, 416E, 416F, 420D, 420E, 420F, 430D, 430E, 430F, 450E, 450F
2298911
PISTON
416E, 416F, 420E, 420F, 422E, 428E, 430E, 430F, 432E, 434E, 442E, 444E
416E, 416F, 420E, 420F, 422E, 428E, 430E, 430F, 432E, 434E, 442E, 444E
2283473
PISTON
430E, 430F, 442E, 444E
430E, 430F, 442E, 444E
3358210
PISTON ROD
414E, 416E, 422E, 424B, 428E, 434E
414E, 416E, 422E, 424B, 428E, 434E
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 414E, 416E, 422E, 424B, 424B HD, 428E, 434E, 621H, 621K, 623H, 623K LRC, 627H, 627K LRC
420E, 420F, 432E, 434E
2529732
PISTON
420E, 432E, 434E
420E, 432E, 434E
2332579
PISTON
420D, 420E, 430D, 430E
420D, 420E, 430D, 430E