3343747 PISTON & ROD GP Caterpillar parts
416E, 422E, 422F
Rating:
Alternative (cross code) number:
CA3343747
334-3747
3343747
CA3343747
334-3747
3343747
BACKHOE LOADER,
Information:
Specifications
Illustration 5 g03320006
Table 2
Tool Specifications    
Condition     Working Load Limit (WLL)     Size     Weight    
Expanded (A)     159 kg (350 lb)    
1647.95 x 736.6 mm (64.9 x 29 in)    
31 kg (68 lb)    
Contracted (B)    
408 kg (900 lb)    
1076 x 538.52 mm (42.4 x 21.2 in)    
31 kg (68 lb)    The dimensions shown in the Tool Specifications table are for the vertical length and the horizontal width. The outer-most tubing near the center of the contracted tool (two small spacers that host the bolt and nut for the outer vertical tubing) has a diameter of 69.85 mm (2.75 in).Note: For more information on setting the extension arms length, refer to the specific Disassembly and Assembly service manual for the component to be lifted.Operation Section
Operation
Note: The adjustable C-frame assembly weighs 31 kg (68 lb).
Due to the shape and weight of the tool, use a suitable lifting device or get help when lifting the C-frame assembly.
Illustration 6 g03321612
Identify the load and weight of the machine component to be lifted. Do not exceed the Working Load Limit (WLL).
Make sure that the lifting eyebolt is fully inserted. Tighten to standard torque.
After achieving desired length, make sure that bolts are fully inserted and tightened with nuts to standard torque.
Illustration 7 g03322081
Identify and measure the desired vertical length of the tooling required for the operation and adjust the inner vertical tube at the desired settings before loading the tool onto a suitable hoist or lifting device.Note: The Working Load Limit (WLL) of the tooling changes as the vertical length of the tooling changes.Note: The bolts and nuts used to keep the vertical tubes at the desired lengths should be tightened to standard torque before proceeding to the next step.Note: This step requires the tool to be laying flat on the surface or ground.
Illustration 8 g03322137
Attach a suitable hoist or lifting device to the upper eyebolt assembly (2) .Note: The Working Load Limit (WLL) of the hoist or lifting device used for this step should be more than the weight of the machine component being lifted and the tooling used to lift it.
Refer to the appropriate Disassembly and Assembly service manual for the machine component to be lifted.
Illustration 9 g03322200
Turn the hex nuts (5) with a 22.22 mm (7/8 in) hand wrench until the desired horizontal location is achieved.Note: The Working Load Limit (WLL) of the tooling changes as the horizontal length of the tooling changes.Note: Avoid getting trapped between tooling and the machine component. Stay a safe distance away from the tooling and the machine component during the installation and removal of the machine component.Note: Operate the wrench by hand only, and when the tool is in a stable condition.Inspection and Maintenance Section
Inspection
Illustration 10 g03322272
Inspect all welds and check for damaged, cracked, or bent components. Inspect tooling prior to each use. If damage is found, destroy the tool and dispose of as scrap. Replace damaged tool with new product.
Do not use unless the Working Load Limit (WLL) identification markings
Illustration 5 g03320006
Table 2
Tool Specifications    
Condition     Working Load Limit (WLL)     Size     Weight    
Expanded (A)     159 kg (350 lb)    
1647.95 x 736.6 mm (64.9 x 29 in)    
31 kg (68 lb)    
Contracted (B)    
408 kg (900 lb)    
1076 x 538.52 mm (42.4 x 21.2 in)    
31 kg (68 lb)    The dimensions shown in the Tool Specifications table are for the vertical length and the horizontal width. The outer-most tubing near the center of the contracted tool (two small spacers that host the bolt and nut for the outer vertical tubing) has a diameter of 69.85 mm (2.75 in).Note: For more information on setting the extension arms length, refer to the specific Disassembly and Assembly service manual for the component to be lifted.Operation Section
Operation
Note: The adjustable C-frame assembly weighs 31 kg (68 lb).
Due to the shape and weight of the tool, use a suitable lifting device or get help when lifting the C-frame assembly.
Illustration 6 g03321612
Identify the load and weight of the machine component to be lifted. Do not exceed the Working Load Limit (WLL).
Make sure that the lifting eyebolt is fully inserted. Tighten to standard torque.
After achieving desired length, make sure that bolts are fully inserted and tightened with nuts to standard torque.
Illustration 7 g03322081
Identify and measure the desired vertical length of the tooling required for the operation and adjust the inner vertical tube at the desired settings before loading the tool onto a suitable hoist or lifting device.Note: The Working Load Limit (WLL) of the tooling changes as the vertical length of the tooling changes.Note: The bolts and nuts used to keep the vertical tubes at the desired lengths should be tightened to standard torque before proceeding to the next step.Note: This step requires the tool to be laying flat on the surface or ground.
Illustration 8 g03322137
Attach a suitable hoist or lifting device to the upper eyebolt assembly (2) .Note: The Working Load Limit (WLL) of the hoist or lifting device used for this step should be more than the weight of the machine component being lifted and the tooling used to lift it.
Refer to the appropriate Disassembly and Assembly service manual for the machine component to be lifted.
Illustration 9 g03322200
Turn the hex nuts (5) with a 22.22 mm (7/8 in) hand wrench until the desired horizontal location is achieved.Note: The Working Load Limit (WLL) of the tooling changes as the horizontal length of the tooling changes.Note: Avoid getting trapped between tooling and the machine component. Stay a safe distance away from the tooling and the machine component during the installation and removal of the machine component.Note: Operate the wrench by hand only, and when the tool is in a stable condition.Inspection and Maintenance Section
Inspection
Illustration 10 g03322272
Inspect all welds and check for damaged, cracked, or bent components. Inspect tooling prior to each use. If damage is found, destroy the tool and dispose of as scrap. Replace damaged tool with new product.
Do not use unless the Working Load Limit (WLL) identification markings
Caterpillar SIS machinery equipment:
Caterpillar SIS
422E Backhoe Loader DSK00001-UP (MACHINE) POWERED BY C4.4 (MECH) Engine »
334-3747
PISTON & ROD GP
422E Backhoe Loader MAW00001-UP (MACHINE) POWERED BY C4.4 Engine »
334-3747
PISTON & ROD GP
422E Backhoe Loader MAW00001-UP (MACHINE) POWERED BY C4.4 Engine »
334-3747
PISTON & ROD GP
416E Backhoe Loader Single Tilt LMS00001-UP (MACHINE) POWERED BY C4.4 Engine »
334-3747
PISTON & ROD GP
422F Backhoe Loader LRH00001-UP (MACHINE) POWERED BY C4.4 Engine »
334-3747
PISTON & ROD GP
422F2 Side Shift Backhoe Loader LYF00001-UP (MACHINE) POWERED BY C4.4 Engine »
334-3747
PISTON & ROD GP
Caterpillar parts catalog:
Parts piston Caterpillar catalog:
4T7010
PISTON
414E, 416, 416B, 416C, 416D, 416E, 422E, 424D, 426, 426B, 428, 428B, 428C, 438C
414E, 416, 416B, 416C, 416D, 416E, 422E, 424D, 426, 426B, 428, 428B, 428C, 438C
1210714
PISTON
414E, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430D, 430E, 432D, 434E, 436C, 438C, 438D, 442D, 444E
414E, 416C, 416D, 416E, 420D, 420E, 422E, 424D, 426C, 428C, 428D, 428E, 430D, 430E, 432D, 434E, 436C, 438C, 438D, 442D, 444E
1683384
PISTON AS-PUMP
246D, 24M, 262D, 272D, 277D, 279D, 287D, 289D, 299D, 305.5E, 345D, 345D L, 345D L VG, 349D, 349D L, 35, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 414E, 416E, 416F, 422E, 422F, 424B...
246D, 24M, 262D, 272D, 277D, 279D, 287D, 289D, 299D, 305.5E, 345D, 345D L, 345D L VG, 349D, 349D L, 35, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 414E, 416E, 416F, 422E, 422F, 424B...
1990752
PISTON-BRAKE
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
414E, 416E, 416F, 420E, 420F, 422E, 422F, 428E, 428F, 430E, 430F, 432E, 432F, 434E, 434F, 442E, 444E, 444F, TH103, TH460B, TH560B, TH580B
2255437
PISTON AS
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315C, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 4...
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 315C, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430E, 430F, 432D, 432E, 432F, 434E, 434F, 4...
2881394
PISTON AS
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
2881395
PISTON AS
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
3054C, 3054E, 312D2, 312D2 GC, 312D2 L, 313D2, 313D2 LGP, 318D2 L, 414E, 416D, 416E, 416F, 420D, 420E, 420F, 422E, 422F, 424D, 428D, 428E, 428F, 430D, 430F, 432D, 432E, 432F, 434E, 434F, 442D, 442E, 4...
2332583
PISTON
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 450E, 527
416D, 416E, 420D, 420E, 422E, 424D, 428D, 428E, 430D, 430E, 432D, 432E, 434E, 442D, 442E, 444E, 446D, 450E, 527
3203619
PISTON
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
422E, 422F, 428E, 428F, 432E, 432F, 434E, 434F, 442E, 444E, 444F
7W4703
PISTON & ROD GP
224, AP-1200
224, AP-1200
1979385
PISTON & ROD GP
C-9, C9
C-9, C9
2218453
PISTON GP
G3516C
G3516C
0929004
PISTON & INSERT AS
WE-601B
WE-601B
1315594
PISTON & ROD GP
3054, PS-200B, TH103, TH62, TH63, TH82, TH83
3054, PS-200B, TH103, TH62, TH63, TH82, TH83
2808704
PISTON GP
G3520B
G3520B
3111101
PISTON & ROD GP
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34, CB22B, CB24B, CB32B, CC24B
2263825
PISTON GP
G3520B
G3520B