3G1753 PISTON Caterpillar parts
140B, 14G, 16G, 977, D4E, D4E SR, D5H, D5H XL, D6H, D6H XL, D6H XR, D6K LGP, D6M, D6N, D6R, D6R II, D6R III, D6T
Rating:
Alternative (cross code) number:
CA3G1753
3G-1753
3G1753
CA3G1753
3G-1753
3G1753
Weight: 10 pounds 4 kg.
Information:
PISTON DIAMETER
50.815
mm
THICKNESS
68
mm
NUMBER OF C BORE
1
Wear Ring Dia
120.42
NOMINAL CYLINDER BORE
127
NOMINAL ROD DIAMETER
82.55
MOTOR GRADER, TRACK-TYPE TRACTOR,
Compatible equipment models: 3G1753:
Information:
Assembly Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     134-2837     Piston Compressor     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009791
Typical example
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Note: Never use rags to clean the compression brake housing or any of the components. Rags may leave lint or residue that can obstruct oil passages.
Thoroughly clean the compression brake housing and all of the components with an approved solvent. Dry the compression brake housing and the solenoid valve with 103 to 138 kPa (15 to 20 psi) of compressed air.
Install master piston (15), pushrod (16), master piston spring (17), retaining washer (18), and retaining ring (19) .
Illustration 2 g01009784
Typical example
Illustration 3 g00512594
Typical example
Install slave piston (9), outer spring (10), pushrod (11), inner spring (12), and retaining washer (13) .
Use Tooling (A) to compress the assembly until retaining washer (13) is approximately 1.00 mm (0.039 inch) below the retaining ring groove. Install retaining ring (14). Ensure that retaining ring (14) is properly seated in the groove.
Remove Tooling (A) .
Illustration 4 g01009783
Typical example
Inspect slave piston adjustment screw (7). The plunger should protrude from the bottom of slave piston adjusting screw (7). Approximately 53 N (12 lb) of force is required to move the plunger. Ensure that the spring retaining pin for the plunger is seated.
Install slave piston adjusting screw (7) and slave piston adjustment screw locknut (8). Do not tighten the assembly at this time.Note: Refer to Testing and Adjusting, "Slave Piston Lash - Adjust" for more information on the adjustment of the slave piston lash.
Illustration 5 g01009776
Typical example
Push a wire through the hole in the base of control valve (5) in order to ensure that the check ball is free. The check ball should unseat with slight pressure on the wire. If the check ball is stuck, replace the control valve.
Put clean engine oil on control valve (5) and install the control valve in the compression brake housing. If binding occurs, replace the control valve. Install control valve springs (6) .
Put control valve cover (3) in position and install allen head screw (4) .
Illustration 6 g00512487
Typical example
Use new seals (2). Coat the seals with clean engine oil. Install the upper seal and the center seal on the solenoid body. Install the lower seal in the bottom of the bore for the solenoid valve in the compression brake housing.
Ensure that seals (2) are seated properly. Carefully install solenoid valve (1) in the compression brake housing. Tighten the solenoid valve to a torque of 12.4 N m (110 lb in). Be careful not to twist the seals during installation.End By: Install the compression brake. Refer to Disassembly and Assembly, "Compression Brake - Install".
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     134-2837     Piston Compressor     1    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01009791
Typical example
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Note: Never use rags to clean the compression brake housing or any of the components. Rags may leave lint or residue that can obstruct oil passages.
Thoroughly clean the compression brake housing and all of the components with an approved solvent. Dry the compression brake housing and the solenoid valve with 103 to 138 kPa (15 to 20 psi) of compressed air.
Install master piston (15), pushrod (16), master piston spring (17), retaining washer (18), and retaining ring (19) .
Illustration 2 g01009784
Typical example
Illustration 3 g00512594
Typical example
Install slave piston (9), outer spring (10), pushrod (11), inner spring (12), and retaining washer (13) .
Use Tooling (A) to compress the assembly until retaining washer (13) is approximately 1.00 mm (0.039 inch) below the retaining ring groove. Install retaining ring (14). Ensure that retaining ring (14) is properly seated in the groove.
Remove Tooling (A) .
Illustration 4 g01009783
Typical example
Inspect slave piston adjustment screw (7). The plunger should protrude from the bottom of slave piston adjusting screw (7). Approximately 53 N (12 lb) of force is required to move the plunger. Ensure that the spring retaining pin for the plunger is seated.
Install slave piston adjusting screw (7) and slave piston adjustment screw locknut (8). Do not tighten the assembly at this time.Note: Refer to Testing and Adjusting, "Slave Piston Lash - Adjust" for more information on the adjustment of the slave piston lash.
Illustration 5 g01009776
Typical example
Push a wire through the hole in the base of control valve (5) in order to ensure that the check ball is free. The check ball should unseat with slight pressure on the wire. If the check ball is stuck, replace the control valve.
Put clean engine oil on control valve (5) and install the control valve in the compression brake housing. If binding occurs, replace the control valve. Install control valve springs (6) .
Put control valve cover (3) in position and install allen head screw (4) .
Illustration 6 g00512487
Typical example
Use new seals (2). Coat the seals with clean engine oil. Install the upper seal and the center seal on the solenoid body. Install the lower seal in the bottom of the bore for the solenoid valve in the compression brake housing.
Ensure that seals (2) are seated properly. Carefully install solenoid valve (1) in the compression brake housing. Tighten the solenoid valve to a torque of 12.4 N m (110 lb in). Be careful not to twist the seals during installation.End By: Install the compression brake. Refer to Disassembly and Assembly, "Compression Brake - Install".
Cat SIS web machinery list:
Parts piston Caterpillar catalog:
7J5682
PISTON
120G, 12G, 130G, 140G, 14G, 16G, 227, 518, 518C, 627E, 637E, 657E, 910, 931B, 950
120G, 12G, 130G, 140G, 14G, 16G, 227, 518, 518C, 627E, 637E, 657E, 910, 931B, 950
7T3566
PISTON
D6H, D7H, D8N
D6H, D7H, D8N
9T8452
PISTON
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 24H, 24M, 5230, 5230B, 789B, 789C, 789D, 793, 793B, 793C, D8N, D8R, D8R II, D9R
14G, 14H, 14H NA, 14M, 16G, 16H, 16H NA, 16M, 24H, 24M, 5230, 5230B, 789B, 789C, 789D, 793, 793B, 793C, D8N, D8R, D8R II, D9R
9T5927
PISTON
16G, 16H, 16H NA, 16M, 345B II, 345B L, 345C L, 349E L HVG, 910E, 910G, 914G, 918F, 924F, 980G, 980G II, 980H, IT12B, IT14G2, R1300, R1300G, R1300G II
16G, 16H, 16H NA, 16M, 345B II, 345B L, 345C L, 349E L HVG, 910E, 910G, 914G, 918F, 924F, 980G, 980G II, 980H, IT12B, IT14G2, R1300, R1300G, R1300G II
4D0532
PISTON ASSEM
140B, 14E, 910
140B, 14E, 910
8D4291
PISTON
12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14G, 14H, 14H NA, 160G, 160H, 515, 525
12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14G, 14H, 14H NA, 160G, 160H, 515, 525
3P0315
PISTON-CLUTCH
120G, 12G, 130G, 14G, 16G
120G, 12G, 130G, 14G, 16G
2P4510
PISTON-CLUTCH
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
7T9647
PISTON-CLUTCH
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA
3P2874
PISTON-CLUTCH
14G, 16G
14G, 16G
3P1651
PISTON AS
14G, 14H, 14H NA, 16G, 16H, 16H NA
14G, 14H, 14H NA, 16G, 16H, 16H NA
6G6264
PISTON
14G, 14H, 14H NA, 16G, 16H, 16H NA
14G, 14H, 14H NA, 16G, 16H, 16H NA
9T3885
PISTON AS
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR
D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7H, D7R, D7R II, D7R XR
2238073
PISTON
D6R, D6R II
D6R, D6R II
3W0640
PISTON
517, 527, 572R, 572R II, D5HTSK II, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR
517, 527, 572R, 572R II, D5HTSK II, D6H, D6H II, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7R, D7R II, D7R XR
8P1892
PISTON-CLUTCH
572R, 572R II, 578, 583R, 587R, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D7H, D7R, D7...
572R, 572R II, 578, 583R, 587R, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D7H, D7R, D7...
9G0285
PISTON-CLUTCH
572R, 572R II, 578, 583R, 615, 615C, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, D25C, D300B, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD,...
572R, 572R II, 578, 583R, 615, 615C, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, D25C, D300B, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD,...
6V2598
PISTON MOTOR
943, 953, 963
943, 953, 963
8Y1770
PISTON AS
973, 973C
973, 973C
3W8158
PISTON AS
963, 963B, 963C, 963D, 973, 973C
963, 963B, 963C, 963D, 973, 973C
2238072
PISTON
D6R, D6R II
D6R, D6R II
3679479
PISTON
D6H XL, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL
D6H XL, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL
1181170
PISTON AS
D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7R
D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T XL, D7R
4T0259
PISTON
D5H XL, D5R LGP, D6H, D6H XL, D6H XR, D6N, D6N LGP, D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL
D5H XL, D5R LGP, D6H, D6H XL, D6H XR, D6N, D6N LGP, D6R, D6R II, D6R III, D6T, D6T LGP, D6T XL