AVSPARE.COM
parts catalog

PISTON 6E1328 - Caterpillar


6E1328 PISTON Caterpillar parts
Rating:
66
Alternative (cross code) number:
CA6E1328
6E-1328
6E1328
Caterpillar 6E1328 PISTON
Weight: 0.42 pounds 0 kg.

Buy PISTON 6E1328 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 15 g02283033
Portable hydraulic tester (flow meter) (5) Load valve
Illustration 16 g02487358
Hold the left joystick in the FULL BACKWARDS position. Turn load valve (5) on the flow meter until the pressure reading is 15000 kPa (2176 psi). Adjust the flow rate using the left and right arrows on the monitor until the flow meter reads 300 L/min (79.3 US gpm). Press the OK key.Note: Adjusting the load valve on the flow meter to maintain the specified pressure must be done after the flow rate is changed.Note: The joystick must be held in the FULL BACKWARDS position for the duration of the test.
Illustration 17 g02487576
Release the left joystick back to the NEUTRAL position.
Illustration 18 g02487580
All levers become enabled. Press the OK key.
Illustration 19 g02487761
For machines configured with a One-Way flow system, if calibration was successful and no errors occurred, the display will indicate that the calibration is complete. If the machine is configured with a Two-Way flow system, proceed to Step 13.
Close the stop valves on each side of the stick.
Release pressure in the hydraulic system. Refer to Testing and Adjusting, "System Pressure - Release".
Reverse the flow meter lines location on the stop valves for Two-Way flow.Note: To calibrate the retraction of the attachment control valve, the direction of oil flow through system will be reversed. To protect the flow meter from damage, the orientation of the flow meter must also be reversed.
Open the stop valves on each side of the stick.
Illustration 20 g02487636
Close the ball valves on the main control valve for Two-Way flow. Refer to Illustration 6 for the appropriate setting.
Illustration 21 g02487656
Set the hydraulic lock lever to the UNLOCK position.
Illustration 22 g02487676
All levers become enabled. Press the OK key.
Illustration 23 g02487756
Hold the left joystick in the FULL BACKWARDS position. Turn load valve (5) on the flow meter until the pressure reading is 15000 kPa (2176 psi). Adjust the flow rate using the left and right arrows on the monitor until the flow meter reads 300 L/min (79.3 US gpm). Press the OK key.Note: Adjusting the load valve on the flow meter to maintain the specified pressure must be done after the flow rate is changed.Note: The joystick must be held in the FULL BACKWARDS position for the duration of the test.
Illustration 24 g02487757
Release the left joystick back to the NEUTRAL position.
Illustration 25 g02487758
All levers become enabled. Press the OK key.
Illustration 26 g02487761
If calibration was successful and no errors occurred, the display will indicate that the calibration is complete.
Illustration 27 g02487763
The "Error" screen will be displayed on the monitor if an error occurs. The process of calibration will not be saved and the process must be restarted.


Parts piston Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.