PLANETARY GP-FINAL DRIVE 2013413 - Caterpillar

Install shield (28) on the top right side of the shield assembly. Fasten the shield using seven bolts (11) with seven hard washers (6).
Illustration 72 g03896442
(6) 5P-1075 Hard Washers
(11) 5P-8167 Bolts
(29) 485-5654 Shield
Install shield (29) on the top left side of the shield assembly. Fasten the shield using seven bolts (11) with seven hard washers (6).
Illustration 73 g03896450
(6) 5P-1075 Hard Washers
(11) 5P-8167 Bolts
(30) 485-8339 Shield
Install shield (30) using two bolts (11) with two hard washers (6).
Illustration 74 g03896456
(6) 5P-1075 Hard Washers
(11) 5P-8167 Bolts
(31) 485-8340 Shield
Install shield (31) using two bolts (11) with two hard washers (6) on the right side of the engine. Leave the bolts hand tight until the next step.
Illustration 75 g03896464
(6) 5P-1075 Hard Washers
(11) 5P-8167 Bolts
(32) 482-7031 Shield
Install shield (32) using two bolts (11) with two hard washers (6). The bolts shown in the bottom of the shield are from the previous step, these bolts can now be tightened.
Illustration 76 g03896469
(33) 372-1186 Nitrogen Oxide Sensor As
(34) 330-5405 Shield
(35) 335-3377 Gasket
(36) 9I-2295 Bolts
(37) 110-8314 Washers
(38) 2B-2694 Bolts
(39) 9N-0869 Hard Washers
(40) 0S-0509 Bolt
(41) 5M-2894 Hard Washers
(42) 4P-8134 Clip
(43) 9X-6772 Cable Strap
(44) 9S-1350 Clip
(45) 0S-1594 Bolt
(46) 9S-8752 Full Nut
Install nitrogen oxide sensor assembly (33) to the front of the shield assembly using four bolts (38) with four hard washers (39).
Install gasket (35) behind shield (34) and fasten using four bolts (36) with four hard washers (37).
Install clip (42) using bolt (40) with hard washer (41). Secure the sensor wire to the clip using cable strap (43).
Install the sensor wire through clip (44). Fasten the clip to the shield using bolt (45) with two hard washers (41) and full nut (46).Register the Retrofit
Because retrofits to a prime product will change the configuration of the product, updating the configuration in SIMSi and AIMS is important. If the retrofit information is not provided, Caterpillar will not be able to provide important product updates.
When performing a retrofit installation, record the vital information in Table 12.Note: If the procedure is performed by the customer, ask the customer to record the proper information.
Table 12
Repair Date
Product Serial Number
Service Hours or Service Meter Units
Removed Component Part Number(1)
Removed Component Serial Number(1)
Installed Component Part Number(2)
Installed Component Serial Number(3)
(1) Only applies if a component is replaced by a retrofit component. If the product is an engine, and the product retrofit is a kit for upgrading the engine, disregard the "Removed Component" information.
(2) Record the highest level retrofit kit, arrangement, or group part number.
(3) Most retrofits will not have a serial number. Exceptions include emissions repower engines and diesel particulate filters.
Update the product configuration by entering the information from Table 12 into SIMSi and AIMS.Note: For retrofits that have a Caterpillar serial number, the AIMS application is "JIZ111-08". For retrofits that do not have a Caterpillar serial number, the AIMS application is "JIZ111-07".
For detailed instructions on updating the product configuration, refer to Special Instruction, REHS5097, "Instructions to Register the Retrofit".