PLANETARY GP-FINAL DRIVE 2264339 - Caterpillar

2264339 PLANETARY GP-FINAL DRIVE Caterpillar parts TH560B, TH580B

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2264339
226-4339
2264339

Caterpillar 2264339 PLANETARY GP-FINAL DRIVE

Buy PLANETARY GP-FINAL DRIVE 2264339 Caterpillar genuine, new aftermarket tractor parts with delivery
TELEHANDLER,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

KENNAMETAL Carbide Coolant Drill 4.8mm TiAlN 135° 2264339

$55.00

05 Nov 2019

-: -

KENNAMETAL Carbide Coolant Drill 4.8mm TiAlN 135° 2264339
Drill Bit Size: 4.8mm || Drill Point Angle: 135 || Finish: TiAlN || Overall Length: 66mm || Shank Diameter:

This part in 1 request: Show. This information for suppliers only!

#396352 2264339

2019-12-05

Number on catalog scheme: 42

Caterpillar 2264339 Parts scheme PLANETARY GP-FINAL DRIVE

For full view, you need register

Compatible equipment models: 2264339:

TELEHANDLER TH560B TH580B Caterpillar

Information:

Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Every time that the crankshaft seal is removed from the wear sleeve, a new wear sleeve and crankshaft seal must be installed.
Illustration 1 g01005029
Illustration 2 g01207497
Attach Tooling (D) to the crankshaft.
Clean the outer diameter of the crankshaft and the inner diameter of the new wear sleeve with Tooling (G).
Apply Tooling (H) to the outer diameter of the crankshaft and the inner diameter of the new wear sleeve.
If the crankshaft seal and the wear sleeve come apart during installation, the crankshaft seal and the wear sleeve must be replaced.
Note: The front crankshaft seal and the wear sleeve cannot be interchanged with the rear crankshaft seal and the wear sleeve.
Do not place engine oil on the crankshaft seal for installation. Lubrication of the crankshaft seal can give a false indication of leakage at a later time.
Illustration 3 g01207499
Place front seal (1) and wear sleeve (2) onto Tooling (D).
Illustration 4 g01051474
Illustration 5 g01005047
Place Tooling (E) onto Tooling (D). Apply Tooling (J) onto the face of the washer on Tooling (F). Install Tooling (F) onto Tooling (E). Tighten the nut until Tooling (E) contacts Tooling (D).
Remove the Tooling from the crankshaft.Installation Procedure For Seals 436-1478 and 436-1479
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Do not place engine oil on the crankshaft seal for installation. Lubrication of the crankshaft seal can give a false indication of leakage at a later time.
Note: Ensure that there are no imperfections on the mating surfaces of the crankshaft, the installation tooling, or on the sealing surface of the crankshaft. Surface imperfections can distort the seal during installation and will cause the seal to malfunction.
Illustration 6 g06042381
Using Tooling (K), install rear seal (1) as outlined in the following steps:
Install pilot (K1) to the crankshaft and install bolts (K2).
Position rear seal (1) onto pilot (K1).
Install driver (K3) onto the shaft of pilot (K1). Mark driver (K3) at the 12 O' Clock position. Install bearing (K4) and nut (K5).
Tighten nut (K5) until the base of driver (K3) contacts the skirt of pilot (K1). Loosen nut (K5) and rotate driver (K3) 180 degree. Retighten nut (K5) until driver (K3) contacts the skirt of pilot (K1).
Remove Tooling (K).End By:
Install the flywheel.