PLATE 0875977 - Caterpillar

Table 5
Effectivity Of The 227-0620 Sight Gauge Gp For Certain Excavators    
Model    Effectivity    Adaptability    
322C     S/N:HEK351
, S/N:; LAR194
, S/N:; C3R296
, and S/N:; M2H288
    S/N:HEK1-350
, S/N:; LAR1-193
, S/N:; C3R1-295
, and S/N:; M2H1-287
   
325C     S/N:BFE1013
, S/N:; G1L218
, S/N:; M2K299
, S/N:; S2C142
, S/N:; S3M324
, and S/N:; Y4P401
    S/N:BFE1-1012
, S/N:; G1L1-217
, S/N:; M2K1-298
, S/N:; S2C1-141
, S/N:; S3M1-323
, and S/N:; Y4P1-400
   
330C     S/N:DKY1600
, S/N:; B1K179
, S/N:; B2L204
, S/N:; B3M197
, S/N:; B4N189
, and S/N:; D3C232
    S/N:DKY1-1599
, S/N:; B1K1-178
, S/N:; B2L1-203
, S/N:; B3M1-196
, S/N:; B4N1-188
, and S/N:; D3C1-231
   
345B Series II     S/N:AGS1910
, S/N:; ALB356
, S/N:; APB261
, S/N:; CDY313
, and S/N:; DCW316
    S/N:AGS1-1909
, S/N:; ALB1-355
, S/N:; APB1-260
, S/N:; CDY1-312
, and S/N:; DCW1-315
   
Table 6
Effectivity Of The 223-3095 Gauge For Certain Excavators    
Model    Effectivity    Adaptability    
345B Series II     S/N:AGS1995
, S/N:; ALB358
, S/N:; APB264
, S/N:; CDY313
, S/N:; CFM286
and S/N:; DCW318
    S/N:AGS1-1994
, S/N:; ALB1-357
, S/N:; APB1-263
, S/N:; CDY1-312
, S/N:; CFM1-285
, and S/N:; DCW1-317
   
Illustration 1 g01031871
227-0620 Sight Gauge Gp (A) 236-3259 Bolt (B) 236-3258 Block (C) 095-1519 O-Ring Seal (D) 6F-4855 O-Ring Seal (E) 236-3257 Pipe
Illustration 2 g01031872
223-3095 Gauge (F) 237-8526 Pipe (G) Bar For The Gauge (H) 237-8862 Spacer (J) 6V-8398 O-Ring Seal Procedure For The Replacement Of A Sight Gauge
Make sure that the residual fuel or oil has been removed from the threads of the boss on the tank before installing a new gauge. Use isopropyl alcohol in order to clean the threads. The performance of the thread lock will be ineffective if the threads are not correctly cleaned.
Hand tighten the bolts in order to install the new gauge in the correct position. Use a wrench in order to tighten the bolts if the thread compound makes hand tightening difficult.
The block on the top and the block on the bottom will not stay in the correct position when the bolt is tightened. Use the straight bar in order to tighten the bolts and keep the bracket in the correct position. Torque the bolts to 6 1 N m (5 1 lb ft). Make sure that the brackets at the top and at the bottom are positioned perpendicular.
Installation of a new sight gauge on a fuel tank that uses a bar will require the additional washers that are listed in Table 2. The location of the components is shown in Illustration 2.