PLATE, PORT, FR. 0963993 - Caterpillar

Engine:
G3508 (S/N: 9TG1-UP; WPM1-UP; WPN1-UP; DLR1-UP)
G3508B (S/N: RBK1-UP)
G3512 (S/N: 7NJ1-UP; CSP1-UP; WPP1-UP; WPR1-UP; GNS1-UP)
G3512B (S/N: JHH1-UP)
G3512E (S/N: SSR1-UP; NGS1-UP; GHD1-UP; GYM1-UP)
G3516 (S/N: 4EK1-UP; WPS1-UP; WPT1-UP; WPW1-UP; CSZ1-UP; CTL1-UP)
G3516B (S/N: ZBB1-UP; CSC1-UP; ZBC1-UP; CME1-UP; JEF1-UP; CEY1-UP; 7EZ1-UP; CTW1-UP)
G3516C (S/N: GSB1-UP; TJB1-UP; GZC1-UP; TJC1-UP; GZZ1-UP; F6H1-UP; F6J1-UP; F6K1-UP; DKR1-UP)
G3516E (S/N: GAS1-UP; SLY1-UP; F6L1-UP)
G3520 (S/N: HET1-UP; 5XW1-UP)
G3520B (S/N: CWD1-UP; GLF1-UP; GZP1-UP; GET1-UP; BGW1-UP; CTK1-UP)
G3520C (S/N: GZA1-UP; HEA1-UP; GZB1-UP; HEB1-UP; MAD1-UP; GZJ1-UP; GZK1-UP; GZL1-UP; GZM1-UP; GZN1-UP; B9P1-UP; RLP1-UP; LGS1-UP; HAT1-UP; CWW1-UP; CWY1-UP; GDB1-UP; GHE1-UP)
G3520E (S/N: GZE1-UP; GZG1-UP; GZH1-UP; HAL1-UP; SXY1-UP; GHM1-UP)
G3606 (S/N: 3XF1-UP; 4ZS1-UP)
G3608 (S/N: 4WF1-UP; BEN1-UP)
G3612 (S/N: BKE1-UP; 1YG1-UP)
G3616 (S/N: BLB1-UP; 4CG1-UP)
Petroleum Engine:
G3520B (S/N: TPC1-UP)
Power Module:
PMG3516 (S/N: CFD1-UP; KAD1-UP)
Engine News SEBD9835, 19 December 2012, "Removal of the Coolant Pressure Switch from Certain G3500 and G3600 Engines". Disregard the previous article, effectivity has been added.If problems occur with the 110-1168 Pressure Switch, perform the following procedure to remove the switch.
Table 1
Required Parts    
Qty     Part    
1     1U-5804 Crimp Tool    
Varies     Coolant recommended by the engine Operation and Maintenance Manual    
1     5M-6213 Pipe Plug    
100 to 150 mm     5P-5623 Electrical Wire    
2     8T-8730 Connector Socket    
1     8T-8731 Connector Plug    
1     8T-8737 Seal Plug    
Drain the engine coolant into a suitable container to a level below the 110-1168 Pressure Switch .Keep the coolant for reuse, if possible.
Remove the pressure switch. Install the 5M-6213 Pipe Plug in place of the switch.
Crimp an 8T-8730 Connector Socket on to each end of a wire to be used as jumper. Connect the jumper wire to terminals "B" and "C" on the harness end of the 8T-8731 Connector Plug in order to create a closed circuit.
Install the 8T-8737 Seal Plug into terminal "A" on the harness end of the 8T-8731 Connector Plug .
Connect the 8T-8731 Connector Plug to the harness breakout that was previously connected to the pressure switch. Use a tie strap to secure the breakout harness to the main engine harness.
Refill the cooling system according to the engine Operation and Maintenance Manual.Note: The 110-1168 Pressure Switch will not be installed on new engine builds. Refer to Table 2 for the new engine build serial numbers.
Table 2
Engine Builds without the 110-1168 Pressure Switch    
S/N:9TG565-UP    
S/N:DLR127-UP    
S/N:WPM102-UP    
S/N:WPN1659-UP    
S/N:RBK1305-UP    
S/N:7NJ1366-UP    
S/N:GNS113-UP    
S/N:GYM300-UP    
S/N:WPP1568-UP    
S/N:WPR1630-UP    
S/N:CSP259-UP    
S/N:JHH1024-UP    
S/N:GHD189-UP    
S/N:NGS158-UP    
S/N:SSR192-UP    
S/N:4EK5302-UP    
S/N:CSZ903-UP    
S/N:CTL872-UP    
S/N:F6H101-UP    
S/N:F6J100-UP    
S/N:F6K100-UP    
S/N:F6L100-UP    
S/N:WPS236-UP    
S/N:WPT1576-UP    
S/N:WPW2940-UP    
S/N:7EZ320-UP    
S/N:CEY165-UP    
S/N:CME301-UP    
S/N:CSC415-UP    
S/N:CTW563-UP    
S/N:JEF2326-UP    
S/N:ZBB408-UP    
S/N:ZBC262-UP    
S/N:DKR104-UP    
S/N:GSB128-UP    
S/N:GZC260-UP    
S/N:GZZ362-UP    
S/N:TJB110-UP    
S/N:TJC820-UP    
S/N:GAS281-UP    
S/N:SLY110-UP    
S/N:HET151-UP    
S/N:BGW131-UP    
S/N:CTK262-UP    
S/N:CWD240-UP    
S/N:GET115-UP    
S/N:GLF1105-UP    
S/N:GZP132-UP    
S/N:TPC1120-UP    
S/N:B9P214-UP    
S/N:CWW302-UP    
S/N:CWY222-UP    
S/N:GDB8-UP    
S/N:GHE252-UP    
S/N:GZA238-UP    
S/N:GZB244-UP    
S/N:GZJ631-UP    
S/N:GZK184-UP    
S/N:GZL147-UP    
S/N:GZM213-UP    
S/N:GZN868-UP    
S/N:HAT212-UP    
S/N:HEA103-UP