PLATE AS 1076813 - Caterpillar

Illustration 8 g06020750
Lifting Device for Pin
(4) Pin
Use a lifting device to position the 389-4897 Pin (4). The weight of the pin is 144 kg (318 lb).Install the 8X-0662 Pin (4) into the pin bore of lift arm and the rod eye end of lift cylinder.
Illustration 9 g06020607
Typical View of Linkage Pin in Pin Bore. Measurements (A) and (B) must be equal.
Measure the distance between the end of the pin and the lift arm. Measure both ends.Position the pin in the pin bore so that there is an equal space at each end of the pin.
Illustration 10 g06020845
Outer Collet and Inner Collet for Rod Eye End on Lift Cylinder
(1) Outside collet
(2) Inside colletNote: The inside collet has a larger hole in the middle for the mounting bolt. The outside collet has a smaller threaded hole for the mounting bolt.
Apply 4C-5599 Anti-Seize Compound (C) to the inside diameter of the collets.
Illustration 11 g06020986
(1) 389-4937 Collet
(4) 389-4897 Pin
(7) 9G-7516 Plug
Illustration 12 g06020988
(2) 389-4917 Collet
(3) 9X-8399 Washer
(4) 389-4897 Pin
(6) 3E-8010 Bolt
(7) 9G-7516 Plug
Illustration 13 g06020990
Apply 4C-5599 Anti-Seize Compound (C) to the outside surface of the 389-4937 Collet (1).Install the collet into the pin bore on the outside of the lift arm.Install three Plugs (7) into the Collet (1). Torque the plugs to 12 3 N m (9 2 ft lb).
Illustration 14 g06020992
Perform the following steps to complete the collet installation process.
Apply 4C-5599 Anti-Seize Compound (C) to the outside surface of the 389-4917 Collet (2).
Install the 389-4917 Collet (2) into the pin bore inside the lift arm.Note: The collets on each end of the pin should extend the same distance from the lift arm.
Apply 4C-5599 Anti-Seize Compound (C) to the plugs.
Install three Plugs (7) into the Collet (1). Torque the plugs to 12 3 N m (9 2 ft lb).
Apply 4C-5599 Anti-Seize Compound (C) to the bolt threads.
Install 3E-8010 Bolt (6) with 9X-8399 Washer (3). The bolt threads should engage the threads inside the 389-4937 Collet (1).Note: Start the bolt from the inside collet on the lift arm.
Illustration 15 g06021137
Perform the following steps to complete the pin installation process.
Tighten 3E-8010 Bolt (6) to a torque of 1800 200 N m (1330 150 lb ft).
Strike the collets and the lift cylinder rod end with a hammer until the bolt torque drops to 950 N m (700 lb ft).
Tighten 3E-8009 Bolt (6) to a torque of 1800 200 N m (1330 150 lb ft).
Strike the collets and the lift cylinder rod end with a hammer until the bolt torque drops to 1600 N m (1180 lb ft).
Tighten 3E-8009 Bolt (6) to a torque of 1800 200 N m (1330 150 lb ft).Note: After the bolt is tightened, each collet should extend the same distance from the lift arm.Torque the bolts after the machine has operated for 8 hours and after the machine has operated for 50 hours.
Repeat Steps 3