1243601 PLATE Caterpillar parts
30/30, DEUCE
Rating:
Alternative (cross code) number:
CA1243601
124-3601
1243601
CA1243601
124-3601
1243601
Weight: 3 pounds 1 kg.
Information:
CENTERLINE OF BOLT TO BOLT/CLIP
245
mm
MOUNTING
BOTH ENDS
MOUNTING BOLT SIZE
0000018.0000
THICKNESS
10
mm
TUBE OFFSET
ABOVE CENTER
TUBE RADIUS
89
mm
VINYL COATED
N
WIDTH
40
mm
TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
29 Dec 2018
19 Hundredths Pounds
Suhner Industrial Products -: Suhner Industri
Suhner 1243601 Box Spanner, ST 17 Type
ST 17 type || Sold in each || Easy to Use
ST 17 type || Sold in each || Easy to Use
$491.05
20 Oct 2017
Palmer Wahl: Palmer Wahl
Palmer Wahl - 12436-01 TC Series Optional Rechargeable Battery PackCharger
Palmer Wahl - 12436-01 TC Series Optional Rechargeable Battery PackCharger
Palmer Wahl - 12436-01 TC Series Optional Rechargeable Battery PackCharger
Number on catalog scheme:
1
For full view, you need register
Information:
Probable Causes
Event Codes
Electrical Connections
Diagnostic Codes
Throttle Signal
Fuel Supply
Air Inlet and Exhaust System
Recommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Event Codes that may Derate Engine Power
A. Certain event codes may derate engine power. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes.
Event Codes
Result: There are no active or logged event codes.
Proceed to Test Step 2.
Result: There are active or logged codes.
Repair: Troubleshoot any codes that are present before continuing with this procedure.
2. Check the Electrical Connections
A. Verify that the following connectors are installed correctly:
• Electrical connectors for the ECM
• Connectors for the wiring harness under the valve cover
• Connectors for the engine speed/timing sensors
Electrical Connections
Result: The electrical connections are OK.
Proceed to Test Step 3.
Result: The electrical connections are NOT OK.
Repair: Refer toTroubleshooting, "Electrical Connectors - Inspect" for the proper troubleshooting procedure.
3. Check for Intermittent Diagnostic Codes
A. Certain diagnostic codes may cause poor performance. Connect Cat ET and check for active codes and/or for logged codes.
Diagnostic Codes
Result: There are no diagnostic codes present.
Proceed to Test Step 4.
Result: There are diagnostic codes present.
Repair: Troubleshoot any codes that are present before continuing with this procedure.
4. Intermittent Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle Signal
Result: The throttle signal is OK.
Proceed to Test Step 5.
Result: The throttle signal is NOT OK.
Repair: Refer to Troubleshooting, "Speed Control - Test".
5. Fuel Supply Pressure
A. Check the fuel pressure. Ensure that the fuel is stable. Refer to Systems Operation/Testing and Adjusting for the procedure to check the fuel pressure manually.
B. Visually check the fuel level.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections.
E. Prime the fuel system if any of the following procedures have been performed:
• Replacement of the fuel filters
• Service on the low-pressure fuel supply circuit
• Replacement of unit injectors
F. Check the fuel tank for foreign objects which may block the fuel supply.
G. Check the fuel filters.
H. Check the fuel quality. Make sure that the fuel meets the requirements of Special Publication, SEBU6250, "Caterpillar Machine Fluids Recommendations".
Fuel Supply Pressure
Result: The fuel supply pressure is OK.
Proceed to Test Step 6.
Result: The fuel supply is NOT OK.
Repair: Make the necessary repair and return the unit to service.
6. Check for a Restriction in the Air Inlet and Exhaust System
A. Ensure that the turbocharger is operating correctly. Periodic inspection and cleaning are recommended for the turbocharger compressor housing (inlet side).
B. Check the air filter restriction indicator.
C. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions
Result: There are no restrictions in the air inlet and exhaust system.
Return the
Event Codes
Electrical Connections
Diagnostic Codes
Throttle Signal
Fuel Supply
Air Inlet and Exhaust System
Recommended Actions
Note: If the problem only occurs under certain conditions, test the engine under those conditions. Examples of certain conditions are high engine speed, full load, and engine operating temperature. Troubleshooting the symptoms under other conditions can give misleading results.
Table 1
Troubleshooting Test Steps Values Results
1. Check for Active Event Codes that may Derate Engine Power
A. Certain event codes may derate engine power. Connect Caterpillar Electronic Technician (ET) and check for active codes and/or for logged codes.
Event Codes
Result: There are no active or logged event codes.
Proceed to Test Step 2.
Result: There are active or logged codes.
Repair: Troubleshoot any codes that are present before continuing with this procedure.
2. Check the Electrical Connections
A. Verify that the following connectors are installed correctly:
• Electrical connectors for the ECM
• Connectors for the wiring harness under the valve cover
• Connectors for the engine speed/timing sensors
Electrical Connections
Result: The electrical connections are OK.
Proceed to Test Step 3.
Result: The electrical connections are NOT OK.
Repair: Refer toTroubleshooting, "Electrical Connectors - Inspect" for the proper troubleshooting procedure.
3. Check for Intermittent Diagnostic Codes
A. Certain diagnostic codes may cause poor performance. Connect Cat ET and check for active codes and/or for logged codes.
Diagnostic Codes
Result: There are no diagnostic codes present.
Proceed to Test Step 4.
Result: There are diagnostic codes present.
Repair: Troubleshoot any codes that are present before continuing with this procedure.
4. Intermittent Throttle Signal
A. Monitor the status for "Throttle Position" on Cat ET. Verify that the status for "Throttle Position" is stable and that the engine is able to reach high idle speed.
Throttle Signal
Result: The throttle signal is OK.
Proceed to Test Step 5.
Result: The throttle signal is NOT OK.
Repair: Refer to Troubleshooting, "Speed Control - Test".
5. Fuel Supply Pressure
A. Check the fuel pressure. Ensure that the fuel is stable. Refer to Systems Operation/Testing and Adjusting for the procedure to check the fuel pressure manually.
B. Visually check the fuel level.
C. Ensure that the fuel supply valve (if equipped) is in the full OPEN position.
D. Check the fuel lines for the following problems: restrictions, collapsed lines, pinched lines and loose connections.
E. Prime the fuel system if any of the following procedures have been performed:
• Replacement of the fuel filters
• Service on the low-pressure fuel supply circuit
• Replacement of unit injectors
F. Check the fuel tank for foreign objects which may block the fuel supply.
G. Check the fuel filters.
H. Check the fuel quality. Make sure that the fuel meets the requirements of Special Publication, SEBU6250, "Caterpillar Machine Fluids Recommendations".
Fuel Supply Pressure
Result: The fuel supply pressure is OK.
Proceed to Test Step 6.
Result: The fuel supply is NOT OK.
Repair: Make the necessary repair and return the unit to service.
6. Check for a Restriction in the Air Inlet and Exhaust System
A. Ensure that the turbocharger is operating correctly. Periodic inspection and cleaning are recommended for the turbocharger compressor housing (inlet side).
B. Check the air filter restriction indicator.
C. Check the air inlet and exhaust system for restrictions and/or leaks.
Restrictions
Result: There are no restrictions in the air inlet and exhaust system.
Return the
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2...
120H, 120H ES, 120H NA, 135H, 135H NA, 213B, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446, 446B, 446D, 45, 525B, 533, 535B, 539,...
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 3176, 3176B, 320 L, 320B, 322 FM L, 322 LN, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, ...
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 24H, 30/30, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3304, 3306...
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, ...
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928F, 928G, 928H, 928HZ, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C, D4H, D4H XL, D4HTS...
30/30, 428, 5130, 65C, 75C, 75D, 85C, 85D, 918F, 924F, 928G, 928H, 928HZ, 938F, 938G, 938G II, 988F, 988F II, AP-1000, AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455...
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 637E, 69D, 735, 735B, 740, 740B, 768C, 769C, 769D, 770, 770G, 770G OEM, 771C, 771D, 772, 772G, 772G OEM, 776C, 776D, 777B, 777D, 777F...
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615, 615C, 814B, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 966D, 966F, 966F II, 966G, 966G II, 970F, 972G, 972G II, 972H, 972K, 972M, 9...
30/30, 572R, 572R II, 578, 583R, 583T, 587R, 587T, 611, 615C, 814B, 814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, 980K, D250E, D250E II, D25D, D300E, D30...
30/30, 517, 527, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, DEUCE
2031069
PLATE
DEUCE
DEUCE
2850542
PLATE GP
DEUCE
DEUCE
2850366
PLATE GP
DEUCE
DEUCE
2850260
PLATE GP
DEUCE
DEUCE
2850235
PLATE GP
DEUCE
DEUCE
2850018
PLATE AS
DEUCE
DEUCE
1247229
PLATE-RETAINER
30/30, DEUCE
30/30, DEUCE
1789561
PLATE-WARNING
30/30, DEUCE
30/30, DEUCE
1789560
PLATE-WARNING
30/30, DEUCE
30/30, DEUCE
1789557
PLATE-WARNING
30/30, DEUCE
30/30, DEUCE
1243600
PLATE
30/30, DEUCE
30/30, DEUCE
1789559
PLATE-WARNING
30/30, DEUCE
30/30, DEUCE