1326534 PLATE-ORIFICE Caterpillar parts
375 L, 525B, 525C, 535B, 535C, 545, 545C, 814F, 814F II, 815F, 815F II, 816F, 816F II, 924F, 938F, 950F II, 960F, 966F II, 970F, D6R II, D7R II, D8R II, D9R, IT18F, IT24F, IT28F, IT38F
Rating:
Alternative (cross code) number:
CA1326534
132-6534
1326534
CA1326534
132-6534
1326534
Weight: 0.15 pounds 0 kg.
EXCAVATOR, WHEEL SKIDDER,
Compatible equipment models: 1326534:
Information:
MID 039 CID 1484 FMI 07Conditions Which Generate This Code:
Illustration 1 g01343739
Connections of the inching pedal switch
This diagnostic code is associated with the inching pedal switch. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 07 means that the ECM is receiving an improper response from the switch.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1484 FMI 07 is active before performing this procedure.Test Step 1. CHECK THE OPERATION OF THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector or the wires from the switch.
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Measure the resistance between contact COM and contact NC. Note the resistance. Expected Result:The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms.Results:
YES - The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms. Proceed to Test Step 2.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Actuate the switch and measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Actuate the switch and measure the resistance between contact COM and contact NC. Note the resistance. Expected Result:The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms.Results:
YES - The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms. Proceed to Test Step 3.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 3. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE WIRE HARNESS.
Connect one lead from the multimeter to contact COM (wire J764-BR(Brown)) of the wire harness connector for the switch.
Connect the other lead from the multimeter to frame ground.
Measure the resistance between contact COM (wire J764-BR(Brown)) and frame ground. Expected Result:The resistance is less than 5
Illustration 1 g01343739
Connections of the inching pedal switch
This diagnostic code is associated with the inching pedal switch. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 07 means that the ECM is receiving an improper response from the switch.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1484 FMI 07 is active before performing this procedure.Test Step 1. CHECK THE OPERATION OF THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector or the wires from the switch.
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Measure the resistance between contact COM and contact NC. Note the resistance. Expected Result:The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms.Results:
YES - The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms. Proceed to Test Step 2.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Actuate the switch and measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Actuate the switch and measure the resistance between contact COM and contact NC. Note the resistance. Expected Result:The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms.Results:
YES - The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms. Proceed to Test Step 3.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 3. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE WIRE HARNESS.
Connect one lead from the multimeter to contact COM (wire J764-BR(Brown)) of the wire harness connector for the switch.
Connect the other lead from the multimeter to frame ground.
Measure the resistance between contact COM (wire J764-BR(Brown)) and frame ground. Expected Result:The resistance is less than 5
Cat SIS web machinery list:
Parts plate Caterpillar catalog:
4T7571
PLATE
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H, 5...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16H, 16H NA, 24H, 5...
2062800
PLATE-DETENT
844H, 854G, 854K, D5N, D6N, D6R, D6R II, D6R III, D6R STD, D6T, D7R II, D7R XR, D8R II
844H, 854G, 854K, D5N, D6N, D6R, D6R II, D6R III, D6R STD, D6T, D7R II, D7R XR, D8R II
2136657
PLATE AS
D6R, D6R II, D6R III, D6R STD, D6T, D7R II, D7R XR, D8R II
D6R, D6R II, D6R III, D6R STD, D6T, D7R II, D7R XR, D8R II
1495470
PLATE
583T, 587R, 587T, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G II, 938H, 950 GC, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D3G, D4G, D5G, D5N, D6N,...
583T, 587R, 587T, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G II, 938H, 950 GC, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D3G, D4G, D5G, D5N, D6N,...
1369297
PLATE
583T, 587R, 587T, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G II, 938H, 950 GC, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D3G, D4G, D5G, D5N, D6N,...
583T, 587R, 587T, 844H, 854G, 854K, 914G, 924G, 924GZ, 924H, 924HZ, 928G, 928H, 928HZ, 930G, 938G II, 938H, 950 GC, 950G, 950G II, 962G, 962G II, 966G, 966G II, 972G, 972G II, D3G, D4G, D5G, D5N, D6N,...
2136658
PLATE AS
D6R II, D6R III, D6T, D7R, D7R II, D7R XR, D8R II
D6R II, D6R III, D6T, D7R, D7R II, D7R XR, D8R II
2643934
PLATE
D6R II, D7R II, D8R II
D6R II, D7R II, D8R II
2004574
PLATE AS
D6R II, D6R III, D7R II, D8R II
D6R II, D6R III, D7R II, D8R II
1881013
PLATE
973C, D6R, D6R II, D6R III, D6R STD, D6T, D7R XR
973C, D6R, D6R II, D6R III, D6R STD, D6T, D7R XR
2486958
PLATE AS
D6R II, D6R III, D6T, D7R II, D8R II
D6R II, D6R III, D6T, D7R II, D8R II
2486957
PLATE
D6R II, D6R III, D6T, D6T XL, D7R II, D8R II
D6R II, D6R III, D6T, D6T XL, D7R II, D8R II
1762504
PLATE AS
D6R II, D7R II, D8R II
D6R II, D7R II, D8R II