PLATE 1374704 - Caterpillar

Illustration 7 g03485900
Click OK - If and when ET provides a warning that the Operating System will be changed.
Illustration 8 g03487493
Illustration 9 g03487401
Eboot
Illustration 10 g06069167
During the Flashing process, the Display will show a status bar indicating the progress of the Eboot. A status bar indicating the progress of the operating system will also appear during the process. Application loading will also appear on the screen at a certain point during the flashing process.
Illustration 11 g03494458
WAIT until “Flash Completed Successfully” displays on the screen then, click “Cat ET.”
Illustration 12 g03494483
After Flashing, change the Communication settings back to “Comm Adapter 3” (or “Comm Adapter 2”).
Connect to Cat ET.
Go to Display > Configurations.
Verify that the Product ID matches the Machine Product ID. If the Product ID does not match the Machine Product ID, change the cycle power to the machine so that the display can re-request the Product ID to match the Machine Product ID.Note: This machine cannot manually change product ID configuration. Changing the product ID configuration is supported in the ECM summary screen in ET, but not in the configuration area.
Illustration 13 g03494716Note: Illustration13 is a sample screenshot for D9TREX00301.
Flashing of the information display will vary between different machines.Flashing Example
The following is an example of the approximate numbers and timing recorded during a Flash without bus traffic.Note: Data Link traffic and timing will vary between machines.
Cat ET shows 18% at 16 seconds.
Cat ET shows 45% at approximately 26 seconds.
Reboot at 38 seconds.
Eboot erasing at 48 seconds.
Eboot loading done at 1:04.
Erasing NOR at 1:05.
Erasing NOR OS space ends at 2:37.
Programming OS starts at 2:38.
Programming OS ends at 6:14.
Display has rebooted, but is older cab file at 6:30.
Cat ET shows 50% at 6:38.
Cat ET shows 90% at 6:45.
Reboots.
Cab file extraction at 7:07.
Reboots and shows new cab file at 8:09.
Cat ET shows 100% at 8:19.Troubleshooting
The following table lists the diagnostic codes for the Graphical Display (MID 53). When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.
Table 1
Product ID Slave
CID967-FMI9 Machine Application Abnormal Update Rate
CID967-FMI2-WCI2 Machine Application Mismatch
CID967-FMI2-WCI1 Machine Application Mismatch
Table 2
Sync Clock (Service Hour Meter)
EID 861 Clock Manual Alignment Required
ECU Power Input Voltage
EID 1378 High ECM Power Input Voltage
EID 1379 Low ECM Power Input Voltage
Table 3
12V Supply (Camera Supply)
CID145-FMI3 12 Volt DC Power Supply Voltage Above Normal
CID145-FMI4 12 Volt DC Power Supply Voltage Below Normal
CID145-FMI6 12 Volt DC Power Supply Current Above Normal
CID145-FMI11 12 Volt DC Power Supply Failure Mode Not Identifiable
CID5993-FMI3 12 Volt DC Power Supply Output#1 Voltage Above Normal
CID5993-FMI4 12 Volt DC Power Supply Output#1 Voltage Below Normal
CID5993-FMI6 12 Volt DC Power Supply Output#1 Current Above Normal
CID5993-FMI11 12 Volt DC Power Supply Output#1 Supply Failure Mode Not Identifiable
CID5994-FMI3 12 Volt DC Power Supply Output#2 Voltage Above Normal
CID5994-FMI4 12 Volt DC Power Supply Output#2 Voltage Below Normal
CID5994-FMI6 12 Volt DC Power Supply Output#2 Current Above Normal
CID5994-FMI11 12 Volt DC Power Supply Output#2 Supply Failure Mode Not Identifiable
Table 4
Data Links
CID247-FMI9 SAE J1939 Data Link Abnormal Update Rate
CID247-FMI14 SAE J1939 Data Link Special Instruction
CID3901-FMI9 Ethernet Data Link #2 Abnormal Update