AVSPARE.COM
parts catalog

PLATE AS-RH 1400049 - Caterpillar



1400049 PLATE AS-RH Caterpillar parts PLATE
Rating:
26
Alternative (cross code) number:
CA1400049
140-0049
1400049
Caterpillar 1400049 PLATE AS-RH

Buy PLATE AS-RH 1400049 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

START BY:1) remove front wheels 1. Remove the cotter pin from the steering tie rod pin. Loosen nut (2) until it is even with the bottom of the pin. Hit the nut with a hammer to loosen the pin from its taper. Move steering tie rod (1) free of the wheel spindle housing.2. Remove cotter pin (6). Remove nut (4) with tool (A). Loosen the pin from its taper. Move steering cylinder (5) free of the wheel spindle housing.3. Remove nuts (3) and the bolts that hold the pins to the wheel spindle housing. Step 4 is for earlier model machines only.4. Remove plugs (7) from wheel lean arm (8) with tool group (B). Steps 5 through 7 are for later model machines only.5. Remove bolt (9) and washer (10) from the ends of the pins that hold the wheel spindle housing to the wheel lean arm. 6. Remove retainer (11) from the wheel lean arm. 7. Remove seal ring (12) from retainer (11). 8. Fasten a hoist to the wheel spindle housing. Remove the pins from the wheel spindle housing and the wheel lean arm with tooling (C). 9. Remove wheel spindle and wheel spindle housing (15). Weight is 300 lb. (136 kg). Remove thrust pack (13) from the wheel lean arm. Remove the O-ring seals and seals (14) from the wheel spindle housing. 10. Remove the upper bearing in the wheel lean arm with tooling (D). Use tooling (D) to remove the lower bearing and the lip type seal from the wheel lean arm.Install Wheel Spindle And Wheel Spindle Housing
1. Remove the nut, washer and the bolt that hold lock (1) in the wheel lean arm. Install bearings (3) in wheel lean arm (2) with tooling (A). Install the bearings so they are even with the outer surfaces of the wheel lean arm. Remove tooling (A). Use tooling (B) to install the lip type seal against bearing (3). Install the seal with the lip out as shown. 2. Install bolt (7), the washer and the nut that hold the lock in the wheel lean arm. Tighten the bolt to a torque of 515 20 lb.ft. (698 27 N m).3. Install two O-ring seals and the two "L" shaped seals (5) in wheel spindle and wheel spindle housing (6).4. Fasten a hoist to the wheel spindle and wheel spindle housing.5. Install three thrust washers (4) in the counterbore in the wheel lean arm. Use clean grease to hold the thrust washers in place. The thrust washer with the smallest inside diameter goes between the two other washers.6. Put wheel spindle and wheel spindle housing (6) in position. The weight is approximately 300 lb. (136 kg). 7. Lower the temperature of two pins (8).8. Install pins (8) with tooling (C). Make sure the groove in the pins are in alignment with the opening in the wheel lean arm. Install the pins so that the end of the pin with the hole with threads is away from


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.