PLATE 1611697 - Caterpillar

1611697 PLATE Caterpillar parts AP-650B, AP-800C, AP-800D, BG-225B, BG-225C

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1611697
161-1697
1611697

Buy PLATE 1611697 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT PAVER,

Compatible equipment models: 1611697:

ASPHALT PAVER AP-650B AP-800C AP-800D BG-225B BG-225C Caterpillar

Number on catalog scheme: 72

For full view, you need register

Information:

Illustration 1 g03427457
Schematic of the "Fuel Shut Off" solenoidThis diagnostic code is recorded when the ECM reads the current of the solenoid as being below normal.The possible causes are listed:
There is an open in the circuit.
The solenoid has failed.
The Machine ECM has failed. This situation is unlikely.Note: The following procedure can create numerous related diagnostic codes. When all harnesses are reconnected, the related diagnostic codes will be shown as being not active. Clear all related diagnostic codes after this procedure is completed.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. DO NOT start the engine.
Disconnect the machine harness from the solenoid.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire A982-BR) to frame ground.
Observe the status of the diagnostic code.Expected Result:The diagnostic code is active. Then, the diagnostic code is NOT active as the jumper wire is installed and removed. Results:
YES - The circuit is correct. The solenoid has failed.Repair: Repeat this test "CHECK THE SOLENOID" to verify that the solenoid has failed. Replace the solenoid.STOP
NO - The diagnostic code remains active. Proceed to Test Step 2.Test Step 2. CHECK THE SOLENOID CIRCUIT FOR AN OPEN.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J2 machine harness connector from the ECM.
At the machine harness connector for the solenoid, the jumper wire remains installed.
At J2 machine harness connector, measure the resistance from contact J2-1 (wire A982-BR) to frame ground. Expected Result:The resistance should be less than 5 ohms.Results:
YES - The resistance is less than 5 ohms. The machine harness is correct. Proceed to Test Step 3.
NO - The resistance measurement is NOT correct. There is an open circuit in the machine harness.Repair: The open is in the wire for the solenoid signal or in the ground circuit of the solenoid. Repair the machine harness or replace the machine harness. Repair or replace the ground circuit for the solenoid.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the ON position.
Check if the diagnostic code for the solenoid is active.Expected Result:The diagnostic code is NO longer active. Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP
NO - The diagnostic code has not been corrected. The ECM may have failed.Repair: A failure of the Machine ECM is unlikely. Exit this procedure and perform this procedure again. Also, recheck if the diagnostic indicator is illuminated for this diagnostic code. If the cause of the diagnostic code is not found, replace the ECM. See Testing

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

3054 Engine 6YK00001-UP (MACHINE)

144-3995: CONSOLE GP-OPERATOR » KEBP01110390

CATERPILLAR AP-800C BARBER-GREENE BG-230 Asphalt Pavers 1PM00001-UP (MACHINE) POWERED BY 3054 Engine

144-3995: CONSOLE GP-OPERATOR » KEBP01220391

CATERPILLAR AP-650B, BARBER-GREENE BG-225C Asphalt Pavers 5GN00001-UP (MACHINE) POWERED BY 3054 Engine

115-2298: CONSOLE GP-OPERATOR » KEBP01790252
115-2298: CONSOLE GP-OPERATOR » KEBP01790253
115-2298: CONSOLE GP-OPERATOR » KEBP01790254

AP-800D BG-230D Asphalt Paver A5P00001-UP (MACHINE) POWERED BY 3054C Engine

144-3995: CONSOLE GP-OPERATOR » KEBP02830278

AP-650B BG-225C Asphalt Paver A7P00001-UP (MACHINE) POWERED BY 3054C Engine

115-2298: CONSOLE GP-OPERATOR » KEBP02930212

Parts plate Caterpillar catalog:

1414760 PLATE-COVER
AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C

1149949 PLATE
AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C

1084678 PLATE
AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C

1246300 PLATE
AP-1000B, AP-1055B, AP-650B, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-245C

1228968 PLATE-VALVE
AP-1000B, AP-1055B, AP-1055D, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, AP1000E, AP1055E, AP555E, BG-225B, BG-225C, BG-2455D, BG-245C, BG-260D, BG1000E, BG1055E, BG500E, BG600D, B...

1070995 PLATE
AP-800C, AP-800D, BG-225B

1125375 PLATE AS
AP-800C, AP-800D, BG-225B

2153641 PLATE
AP-1055D, AP-800C, AP-800D, AS2251, AS2301, AS2302, BG-225B, BG-2455D, BG-260D

1931304 PLATE
AP-1055D, AP-800C, AP-800D, AS2251, AS2252C, AS2301, AS2302, BG-225B, BG-2455D, BG-260D

1083289 PLATE AS
AP-650B, AP-800C, AP-800D, BG-225B, BG-225C

1331560 PLATE AS
AP-800C, BG-225B

0870622 PLATE-MOUNTING
AP-1000B, AP-1055B, AP-1055D, AP-1200, AP-600D, AP-650B, AP-655C, AP-655D, AP-800C, AP-800D, AP-900B, BG-225B, BG-225C, BG-2455C, BG-2455D, BG-245C, BG-260D, BG600D, BG655D