1655865 PLATE Caterpillar parts
311C, 312C, 312D
Rating:
Alternative (cross code) number:
CA1655865
165-5865
1655865
CA1655865
165-5865
1655865
Weight: 1 pounds 0 kg.
Information:
ID
66
mm
MATERIAL THICKNESS
3.2
mm
NUMBER OF PITCH HOLES
3
OD
204
mm
PITCH CIRCLE DIAMETER
159
mm
PITCH CIRCLE HOLE DIAMETER
11
mm
EXCAVATOR,
Information:
Keep the engine speed slow until the indicator light for the engine oil pressure goes out.If the light does not go out within ten seconds, stop the engine and investigate the cause before starting the engine again. Failure to correct the problem can cause engine damage.
Illustration 1 g01077703
Note: The hydraulic lockout control must be in the UNLOCKED position before the hydraulic controls will function.
Allow the engine to warm up at low idle for at least five minutes. Engage the joystick controls and disengage the joystick controls. This will speed up the warm-up of the hydraulic components.When you idle the machine for warm-up, observe the following recommendations:
If the temperature is greater than 0°C (32°F), warm up the engine for approximately 15 minutes.
If the temperature is less than 0°C (32°F), warm up the engine for approximately 30 minutes.
If the temperature is less than - 18°C (0°F) or if hydraulic functions are sluggish, additional time may be required.
To warm up the hydraulic oil, turn the engine speed dial to the medium engine speed. Run the engine for approximately five minutes and move the joystick intermittently from the BUCKET DUMP position to the HOLD position. Do not hold the joystick in the BUCKET DUMP position with the bucket cylinder fully extended for more than 10 seconds.
Turn the engine speed dial to the maximum engine speed and repeat Step 2.This allows the oil to attain relief pressure, which causes the oil to warm up more rapidly.
Cycle all controls in order to circulate warm oil through all hydraulic cylinders and all hydraulic lines, and through the swing motor and travel motors.
When you cycle the machine controls, the machine can move suddenly. Contact between the machine and external objects or ground personnel can result in serious injury or death. Before you cycle the machine controls, the machine should be located in an unobstructed, hazard-free work area that is away from external objects and ground personnel.
Observe the gauges and the indicators frequently during the operation.
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
1768574
PLATE
311C, 312C, 312D
311C, 312C, 312D
2056689
PLATE AS
311C
311C
2056691
PLATE AS
311C
311C
2128473
PLATE
311C, 312C, 312C L, 314C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
311C, 312C, 312C L, 314C, 318C, 319C, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN
2005463
PLATE-TOPS
304, 305
304, 305
2143980
PLATE
303, 304, 305
303, 304, 305
1950004
PLATE AS
311C
311C
1950010
PLATE AS
311C
311C
1848594
PLATE
311C
311C
1848593
PLATE
311C
311C
1910862
PLATE-LOCK
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
2041086
PLATE
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR