1741485 PLATE Caterpillar parts
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
Rating:
Alternative (cross code) number:
CA1741485
174-1485
1741485
CA1741485
174-1485
1741485
Weight: 21 pounds 9 kg.
WHEEL DOZER, WHEEL LOADER,
Compatible equipment models: 1741485:
Information:
Illustration 14 g00655322
Place 8L-5832 Hex Nut (8) on 9X-8907 Hexagon Button Screw (9). Tighten 8L-5832 Hex Nut (8) until hex nut (8) is snug. Tighten 8L-5832 Hex Nut (8) for an additional 180 degrees.
Do not let metal chips or pieces of the rivet fall into the engine.
Illustration 15 g00655325
Clean the fuel injection control linkage and clean the surfaces of the cylinder head that are adjacent to the fuel injection control linkage with shop solvent. Remove the towels and remove all debris very carefully.
Install the 180-7956 Clamp Assembly Kit . Refer to the "Installation Of The 180-7956 Clamp Assembly Kit " section of this publication.Installation Of The 180-7956 Clamp Assembly Kit
Note: The 180-7956 Clamp Assembly Kit is used for the former control linkages only.Note: If the 180-7956 Clamp Assembly Kit is installed, refer to ""Modification of the 128-9640 Injector Synchronization Fixture "".The 180-7956 Clamp Assembly Kit may be installed on the fuel injection control linkage. The 180-7956 Clamp Assembly Kit will increase the strength of the joint.
Illustration 16 g00655326
Install 183-9390 Spacer (10) on fuel injection control linkage (4). Refer to Illustration 16.
Apply 169-5464 Quick Cure Primer to the threaded hole in the 180-7954 Clamp (11). Apply 169-5464 Quick Cure Primer to the threads of screw (13). Allow the primer to dry. The Quick Cure Primer counteracts the effects of the Volatile Corrosion Inhibitor (VCI) paper that was used to package the parts.
Apply 154-9731 Thread Lock Compound to the threaded hole in the 180-7954 Clamp (11). Apply 154-9731 Thread Lock Compound to the threads of screw (13) of clamp assembly. Loosely assemble 180-7954 Clamp (11) and 180-7987 Clamp (12) on fuel injection control linkage (4). Refer to Illustration 16. Be sure that the rivet head or bushing (14) is fully engaged into the counterbore of the clamp assembly.Note: If necessary, use a screwdriver in order to rotate the linkage.
Position the rivet head or the bushing completely into the counterbore of the clamp assembly. Be sure that spacer (10) is held tight between the clamp assembly and the fuel injection control linkage (4). Hold the clamp assembly against spacer (10). Tighten screw (13) on the clamp assembly until screw (13) is snug. Tighten screw (13) for an additional 240 degrees (2/3 turn).
Illustration 17 g00655329
Gently push the power setting lever to open. Verify free movement of the power setting lever.
Illustration 18 g00655331
Move the linkage rod toward the cylinder head with the linkage in the shutoff position. The clamp assembly must not contact the cylinder head. Remove the clamp assembly and grind the clamp assembly in order to provide clearance, if necessary.
Install the injector for cylinder number 1. Install the number 1 rocker arm assembly. Install the lockwire and install the dealer's seal on the fuel setting cover. Assemble the remainder of the engine. Refer to the Disassembly and Assembly Service Manual Module for your engine.Modification of the 128-9640 Injector Synchronization Fixture
Note: The 128-9640 Injector Synchronization Fixture is included in
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
9U1739
PLATE-OUTER
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
4E5609
PLATE
988G, 988H, 988K, 990, 990 II, 990H, 990K, 992G, 992K, R3000H
988G, 988H, 988K, 990, 990 II, 990H, 990K, 992G, 992K, R3000H
1T1315
PLATE-CLUTCH
24H, 24M, 69D, 735, 740, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 773F, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G LRC, 775G OEM, 834G, 834H, 836G, 836H, 844, 844H, 988F II, 988G, 988...
24H, 24M, 69D, 735, 740, 769C, 769D, 770, 771C, 771D, 772, 773B, 773D, 773E, 773F, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G LRC, 775G OEM, 834G, 834H, 836G, 836H, 844, 844H, 988F II, 988G, 988...
2043583
PLATE AS
992G
992G
2043586
PLATE
992G
992G
3P7584
PLATE-CLUTCH
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 994, 994D, D10, D11N, D11R
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992C, 992D, 992G, 992K, 994, 994D, D10, D11N, D11R
1957096
PLATE-WEAR
988F, 988F II, 990 II, 990H, 992C, 992D, 992G, 992K
988F, 988F II, 990 II, 990H, 992C, 992D, 992G, 992K
1957097
PLATE-WEAR
988F, 988F II, 990 II, 990H, 992C, 992D, 992G, 992K
988F, 988F II, 990 II, 990H, 992C, 992D, 992G, 992K
1957098
PLATE-WEAR
988F, 988F II, 990 II, 990H, 992C, 992D, 992G, 992K
988F, 988F II, 990 II, 990H, 992C, 992D, 992G, 992K
1618990
PLATE AS
992G, 992K
992G, 992K
1720844
PLATE-CLUTCH
844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K, 993K
844, 844H, 844K, 854G, 854K, 990 II, 990H, 990K, 992G, 992K, 993K
1970677
PLATE
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 844, 950H, 962H, 990 II, 993K, D11R, D11T
773G, 773G LRC, 773G OEM, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 844, 950H, 962H, 990 II, 993K, D11R, D11T
1485652
PLATE
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
4E8153
PLATE
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K
1116827
PLATE AS
990, 990 II
990, 990 II
1099950
PLATE AS
990, 990 II
990, 990 II
1012062
PLATE
844, 990, 990 II
844, 990, 990 II
4E9730
PLATE
844, 990, 990 II
844, 990, 990 II
1629733
PLATE
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K, 993K
844, 844H, 844K, 854G, 854K, 990, 990 II, 990H, 990K, 992G, 992K, 993K
4E7519
PLATE-CLUTCH
844, 854G, 990, 990 II, 992G
844, 854G, 990, 990 II, 992G
9U0901
PLATE
844, 844H, 990, 990 II, 990H
844, 844H, 990, 990 II, 990H
4E8840
PLATE
844, 844H, 990, 990 II
844, 844H, 990, 990 II
1124186
PLATE
844, 990, 990 II
844, 990, 990 II
4E9550
PLATE AS
844, 990, 990 II
844, 990, 990 II