PLATE AS 1910336 - Caterpillar

1910336 PLATE AS Caterpillar parts 304, 305

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA1910336
191-0336
1910336

Weight: 1 pounds 0 kg.

Buy PLATE AS 1910336 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Genuine Polaris Part Number 1910336 - LINE,BRAKE,UPPER W/BOOT,FTGS for Polaris ATV / Motorcycle / Snowmobile/ or Watercraft

$99.98

03 Feb 2018
38 Hundredths Pounds
Polaris: Polaris

Genuine Polaris Part Number 1910336 - LINE,BRAKE,UPPER W/BOOT,FTGS for Polaris ATV / Motorcycle / Snowmobile/ or Watercraft
Genuine Polaris Part Number 1910336 - LINE,BRAKE,UPPER W/BOOT,FTGS for Polaris ATV / Motorcycle / Snowmobile/ or Watercraft||Buy your parts from the largest Polaris OEM Parts Dealer in the Country||All Genuine Polaris Repair Parts have a 30 Day Manufacturers Warranty||Please do not order by description - Make sure you have the correct Part Number||We charge a 20% restock fee on Returns

Number on catalog scheme: 6

Caterpillar 1910336 Parts scheme PLATE AS

For full view, you need register

Compatible equipment models: 1910336:

MINI HYD EXCAVATOR 304 305 Caterpillar

Information:

Start By:
Remove the ripper lift cylinder. Refer to Disassembly and Assembly, "Ripper Lift Cylinder - Remove and Install". Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01030632
Attach a suitable lifting device to ripper (1). The weight of ripper (1) is approximately 1134 kg (2500 lb). Raise ripper (1). Install suitable blocking under ripper (1). Lower ripper (1) on the blocking.
Illustration 2 g01030633
Remove bolts (2).
Attach a suitable lifting device to link assembly (3). The weight of link assembly is approximately 30 kg (65 lb). Remove pins (4) and remove link assembly (3). Repeat this step for the opposite side.
Illustration 3 g01030634
Attach Tooling (A) and a suitable lifting device to ripper (1). Raise ripper (1) and install Tooling (B).
Illustration 4 g01030638
Remove bolt (5) and pin (6). Repeat this step for the opposite side. Remove ripper (1). The weight of ripper is approximately 386 kg (850 lb).
Illustration 5 g01030640
Attach a suitable lifting device to link assembly (7). The weight of link assembly (7) is approximately 91 kg (200 lb).
Remove bolt (8) and remove pin (9). Repeat this step for the opposite side. Remove link assembly (7). Remove hose assemblies (10) (not shown).
Illustration 6 g01030641
Attach a suitable lifting device to link assembly (11). The weight of link assembly (11) is approximately 57 kg (125 lb).
Use a prybar to move link assembly (11) to the side. Repeat this step for the opposite side.
Illustration 7 g01030643
Illustration 8 g01030644
Attach a suitable lifting device to plate assembly (12). The weight of plate assembly (12) is approximately 148 kg (325 lb). Remove bolts (13). Repeat this step for the opposite side.
Remove bolts (14). Remove plate assembly (12).
Illustration 9 g01030646
Attach a suitable lifting device to link assembly (11). The weight of link assembly (11) is approximately 57 kg (125 lb). Apply tension in order to support link assembly (11).
Remove bolt (15).
Drive pin (16) toward tandem housing (17) (not shown) and remove link assembly (11).
Illustration 10 g01030647
Remove seals (18) from link assembly (3).
Use Tooling (C) to remove bearing (19) from link assembly (3). Repeat this step for the remaining bearings.
Illustration 11 g01030648
Remove seals (20) from link assembly (7). Repeat this step for the opposite end of the link. Repeat this step of the remaining link.
Use Tooling (D) in order to remove bearing (21). Repeat this step for the opposite end of the link. Repeat this step of the remaining link.