1933360 PLATE AS Caterpillar parts
322B L, 325B L
Rating:
Alternative (cross code) number:
CA1933360
193-3360
1933360
CA1933360
193-3360
1933360
EXCAVATOR,
Number on catalog scheme:
7
For full view, you need register
Information:
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 14 g01341366
Illustration 15 g01341418
Lower the temperature of bearings (21). Use Tooling (C) to install bearings (21). Install bearings (21) to dimension (A). Dimension (A) is 8.5 0.5 mm (0.3346 0.0197 inch).
Illustration 16 g01341372
Use Tooling (D) (not shown) to install lip seal (20).
Illustration 17 g01341364
Use Tooling (D) (not shown) to install lip seal (19).
Illustration 18 g01341243
Illustration 19 g01341245
Use two suitable lifting devices to position front axle (13). The weight of front axle (13) is approximately 907 kg (2000 lb).
Illustration 20 g01341344
Install Tooling (B) to support front axle (13).
Illustration 21 g01341343
Install washers (18).
Illustration 22 g01341342
Install washer (17) and plate (16).
Illustration 23 g01341248
Install pin assembly (15) and bolt (14). Apply Tooling (E) to the threads of bolts (14). Tighten bolt (14) to a torque of 105 20 N m (77 15 lb ft).
Illustration 24 g06055023
Connect harness assembly (10). Install bolts (11), (12), and the clips. Repeat for the opposite side.
Illustration 25 g01341193
Connect hose assembly (9), hose assembly (8), and hose assembly (7).
Illustration 26 g01341185
Connect hose assembly (6), hose assembly (5), hose assembly (4), hose assembly (3), and hose assembly (2).
Illustration 27 g01341167
Remove Tooling (A) and Tooling (B) from drawbar (1) and the front axle.
Fill the hydraulic oil. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change" for the correct filling procedures.End By:
Install the wheel lean bar.
Install the front wheels.
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
1348882
PLATE AS
322B L, 322C, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN
322B L, 322C, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN
1348880
PLATE AS
322B L, 322C, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN
322B L, 322C, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN
1348854
PLATE AS
322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D L
322B, 322B L, 322B LN, 322C, 322C FM, 324D, 324D L
1399268
PLATE
322B L
322B L
1214965
PLATE AS
322B, 322B L, 322B LN
322B, 322B L, 322B LN
1214963
PLATE AS
322B, 322B L, 322B LN
322B, 322B L, 322B LN
1261913
PLATE
320B, 322B, 322B L, 325B L, 330B, 330B L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, M325B, M330D, W3...
320B, 322B, 322B L, 325B L, 330B, 330B L, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 345B II, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, M325B, M330D, W3...
4I7716
PLATE
320B, 322 FM L, 322B, 322B L, 325 LN, 325B L, 330, 330 FM L, 330B, 330B L, 330C, 330C FM, 330C L, 345B II
320B, 322 FM L, 322B, 322B L, 325 LN, 325B L, 330, 330 FM L, 330B, 330B L, 330C, 330C FM, 330C L, 345B II
1083823
PLATE
322 FM L, 322B L, 325B L, 330, 330 FM L, 330B L
322 FM L, 322B L, 325B L, 330, 330 FM L, 330B L
1083824
PLATE
322B L, 325B L, 330, 330 FM L, 330B L
322B L, 325B L, 330, 330 FM L, 330B L
322, 322 FM L, 322B, 322B L, 322B LN, OEMS
322B L, 325B L