AVSPARE.COM
parts catalog

PLATE 1963420 - Caterpillar


1963420 PLATE Caterpillar parts 320C FM, 325C, 330C MH
Rating:
48
Alternative (cross code) number:
CA1963420
196-3420
1963420
Caterpillar 1963420 PLATE

Buy PLATE 1963420 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 1963420:

EXCAVATOR  320C FM   325C   330C MH   Caterpillar
Number on catalog scheme: 3
  For full view, you need register

Information:


Illustration 1 g00956810
Schematic of the Modulating Valve (No. 3) for ReverseThis diagnostic code is associated with the Modulating Valve "Reverse". The FMI 05 means that the ECM has determined that the current is below normal.The possible causes of this diagnostic code are listed below:
The solenoid energizer circuit of the modulating valve is open.
The return circuit of the modulating valve is open.
The solenoid has failed.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1403 FMI 05 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:When this diagnostic code is active, the ECM will turn off the current to the failed solenoid.Test Step 1. CHECK THE SOLENOID
Turn the disconnect switch and the key start switch to the ON position. Do not start the engine.
Disconnect the solenoid with the active diagnostic code from the machine harness.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire 751-GN) to contact 2 (wire 975-WH).
Observe the status of the CID 1403 FMI 05.Expected Result:The CID 1403 FMI 05 remains active. The FMI has not changed and the "05" is still active.Results:
YES - The diagnostic code remains active. The jumper wire does not affect the diagnostic code. Proceed to Test Step 2.
NO - The diagnostic is no longer active. The solenoid has failed.Repair: The solenoid has failed. Repeat this Test Step "CHECK THE SOLENOID" in order to verify the solenoid failure. Replace the solenoid. Verify that the new solenoid corrects the problem. Stop.Test Step 2. CHECK THE HARNESS FOR AN OPEN
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector(s) from the ECM.
The jumper wire that was installed in the previous test remains in place.
At the machine harness connector, measure the resistance from signal contact J1-4 (wire 751-GN) to contact J1-7 (wire 975-WH).Expected Result:The resistance is less than 5.0 ohms.Results:
OK - The resistance is less than 5.0 ohms. The machine harness is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5000 ohms. The resistance measurement is not correct. There is an open circuit in the machine harness.Repair: The open is in wire 751-GN or in wire 975-WH of the machine harness. Repair the machine harness or replace the machine harness. Stop.Test Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS
Inspect the contacts of the harness connectors and clean the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Operate the machine.
Check the status of the CID 1403 FMI 05.Expected Result:The CID 1403 FMI 05 is active.Results:
YES - The CID 1403 FMI 05 is active. The diagnostic code has not been corrected. The ECM may have failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this procedure

Caterpillar parts catalog:

Caterpillar parts catalog
330C Hydraulic Material Handler D3C00001-UP (MACHINE) POWERED BY C-9 Engine
325C Material Handler S2C00001-UP (MACHINE) POWERED BY 3126 Engine


Parts plate Caterpillar catalog:

1077694 PLATE-THRUST
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2...
0940580 PLATE
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318B, 318C, 318D...
2095909 PLATE-CAM
315C, 315D L, 318B, 318C, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 32...
5I7789 PLATE
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D ...
1733444 PLATE
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
1733443 PLATE
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
1733450 PLATE-FRICTION
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E, 320E L...
4T9425 PLATE-ISOLATION
225, 227, 235, 235B, 235D, 245, 320B FM LL, 325B L, 325C, 330B L, 330C L, 5130, 5130B, 5230, 5230B, 539, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631E, 631G, 633E II, 637E, 637G, 69D, 769...
1297853 PLATE-CREEP
320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 322C, 322C FM, 323D L, 323D2 L, 323E L, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E...
1673862 PLATE-RETAINER
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 993K
1884167 PLATE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
2042677 PLATE-VALVE
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
1211760 PLATE
320 L, 320B, 320B FM LL, 320B L, 320C, 321B, 322B, 325B, 325C, 330B, 345B L, 365B
1211759 PLATE
320 L, 320B, 320B FM LL, 322B, 325B, 330B, 345B L
1165341 PLATE
322B L, 330B L
5Q3837 PLATE
320B FM LL, 320C FM
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.