AVSPARE.COM
parts catalog

PLATE-CLAMP 1T1498 - Caterpillar


1T1498 PLATE-CLAMP Caterpillar parts 24H, 24M, 988F II
Rating:
16
Alternative (cross code) number:
CA1T1498
1T-1498
1T1498
Caterpillar 1T1498 PLATE-CLAMP
Weight: 2 pounds 1 kg.

Buy PLATE-CLAMP 1T1498 Caterpillar genuine, new aftermarket tractor parts with delivery
MOTOR GRADER, WHEEL LOADER,

Compatible equipment models: 1T1498:

MOTOR GRADER  24H   24M  
WHEEL LOADER  988F II   Caterpillar
Number on catalog scheme: 5
  For full view, you need register

Information:


Illustration 8 g03318731
Use vibratory frequency switch (10) in order to set the vibratory system in the low frequency/high amplitude mode on both drums. Note: Two things indicate when the vibratory system is in the low frequency/high amplitude mode. "Vibratory Frequency Mode Low" will appear on the display. Second, one LED next to vibratory frequency switch (10) will be illuminated.
Illustration 9 g03318732
Use front drum select switch (11) in order to select the front drum.Note: Two things indicate when the machine is in both drums mode. First, "Vibe Drum Select Front" will appear on the display. Second, the center LED next to "front drum" select switch (11) will be illuminated.
Illustration 10 g03319012
Depress auto vibratory decrease switch (12) to select the MANUAL mode.Note: Two things indicate when the vibratory system is in the manual mode. First, "Vibe Turn On Speed % Manual" will appear on the display. Second, none of the LEDs next to auto vibratory decrease switch (12) will be illuminated.
Launch the Plus+1TM program on the computer in order to enable the vibe test mode.Note: First time users need to perform the tasks in the Communication and Connections Wizard. This wizard allows the Windows® operating system to recognize the USB device. Follow the on screen instructions.
Illustration 11 g03319013
Click on "Status" icon (13) .
Check "Active Codes" (14). Clear any open "Active Codes".
Illustration 12 g03319017
Click on "Hydraulics" (15) .
Click on "Vibe Test Mode" (16) .
Illustration 13 g03319018
Click on "Enable" icon (17) in order to enable the "Normal Vibe Test Mode".
When "Normal Vibe Test Mode" is in "Enabled" mode, the Plus+1 program is launched.
Illustration 14 g03319020
Press vibratory control switch (18) on the propel lever. The vibratory control switch must be held in the ON position for at least 2 seconds for the vibratory system to actuate.
Watch pressure on Tool (A) for an initial abrupt increase. Record the highest pressure as the intercircuit relief setting. The intercircuit relief setting should be 25000 2000 kPa (3630 290 psi).
Use vibratory control switch (18) to stop the vibratory system.
Use throttle control switch (3) in order to operate the engine in ECO mode or in low idle.Note: Two things indicate when the engine is in ECO mode. First, "ECO" will appear on the display. Second, the second LED next to throttle control switch (3) will be illuminated. Two things indicate when the engine is at low idle. First, "Low Idle" will appear on the display. Second, the first LED next to the throttle control switch will be illuminated.
Move parking brake switch (2) to the ON position.
Move

Caterpillar parts catalog:

Caterpillar parts catalog
24H Motor Grader 7KK00001-UP (MACHINE) POWERED BY 3412E Engine
24M Motor Grader B9K00001-UP (MACHINE) POWERED BY C18 Engine
24M Motor Grader B9300001-UP (MACHINE) POWERED BY C18 Engine
SUPPLEMENTARY PRODUCT SUPPORT LITERATURE FOR 988F & 988F SER 2ZR00001-UP (MACHINE)


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.