2057770 PLATE AS Caterpillar parts
814F, 814F II, 815F, 815F II, 816F, 816F II
Rating:
Alternative (cross code) number:
CA2057770
205-7770
2057770
CA2057770
205-7770
2057770
Weight: 0.75 pounds 0 kg.
LANDFILL COMPACTOR, WHEEL DOZER,
Compatible equipment models: 2057770:
Number on catalog scheme:
41
For full view, you need register
Information:
Circuit Breaker Reset
Under normal operation, the circuit breaker should never trip. If the circuit breaker does trip, it is probably due to a power surge or an electrical failure within the TechStation. If the circuit breaker trips, follow this procedure:1. Shut the power OFF to the TechStation.2. Thoroughly examine the TechStation internally for any signs of an electrical failure (signs of burn damage or a burnt odor). If there are signs of damage, refer to the Service and Warranty section in this manual. If there are no signs of damage, proceed to the next step.3. Raise the top hood of the TechStation and reset the circuit breaker by pressing the reset button.4. Turn the power ON, be ready to immediately shut the power OFF in the event of a problem. If a problem is encountered or the circuit breaker trips again, refer to the Service and Warranty section in this manual.Optional Accessories
Illustration 9. Additional workspace areas for TechStation (available in March 1996).
(1) Additional shelf. (2) Cup Holder/Ash Tray Accessory. Fully Integrated SIS Workstation
The following software will upgrade the TechStation to directly order parts through your Dealer Business System from within SIS (Fully Integrated SIS Workstation). The following section describes a Fully Integrated SIS Workstation. Call the IWS/DBS Help Desk at (309) 675-4000, and/or contact your SIS Coordinator to find out exactly what is required to have this capability. Communications Manager, PC Support, and either a 5250 Emulation Card or a Network Card, including LAN software, are also required for SIS integration with your Dealer Business System.A Fully Integrated SIS Workstation is a computer system setup with the ability to tie into your Dealer Business System (DBS), and perform business functions such as parts ordering and warranty reporting. There are specific hardware and software requirements for putting together a workstation with this capability.The Deluxe SIS TechStation and the Deluxe SIS/Multimedia TechStations, with or without a printer, meet most of the hardware, and some of the software requirements for an integrated workstation. Deluxe SIS TechStations:In order for the Deluxe SIS TechStations to fulfill all of the hardware requirements, either a 5250 emulation card or a network card for integrating the TechStation to your DBS will need to be added along with an interface cable between the card and the external connector panel on the TechStation. The type of network will determine the type of network card. The most commonly used network cards are the IBM 16/4 Token Ring or the Ethernet card.In order to determine which cable assembly will be required for connecting the network card (internal to the PC) to the rear connector panel on the TechStation, refer to the previous section on Caterpillar Hardware Accessories for part numbers. If a 5250 emulation card is used instead of a network card, the 128-3259 Adapter Cable will interface it to the rear connector panel on the TechStation.In order for the Deluxe SIS TechStations to fulfill all of the software requirements, the following software programs will need to be added.1.
Under normal operation, the circuit breaker should never trip. If the circuit breaker does trip, it is probably due to a power surge or an electrical failure within the TechStation. If the circuit breaker trips, follow this procedure:1. Shut the power OFF to the TechStation.2. Thoroughly examine the TechStation internally for any signs of an electrical failure (signs of burn damage or a burnt odor). If there are signs of damage, refer to the Service and Warranty section in this manual. If there are no signs of damage, proceed to the next step.3. Raise the top hood of the TechStation and reset the circuit breaker by pressing the reset button.4. Turn the power ON, be ready to immediately shut the power OFF in the event of a problem. If a problem is encountered or the circuit breaker trips again, refer to the Service and Warranty section in this manual.Optional Accessories
Illustration 9. Additional workspace areas for TechStation (available in March 1996).
(1) Additional shelf. (2) Cup Holder/Ash Tray Accessory. Fully Integrated SIS Workstation
The following software will upgrade the TechStation to directly order parts through your Dealer Business System from within SIS (Fully Integrated SIS Workstation). The following section describes a Fully Integrated SIS Workstation. Call the IWS/DBS Help Desk at (309) 675-4000, and/or contact your SIS Coordinator to find out exactly what is required to have this capability. Communications Manager, PC Support, and either a 5250 Emulation Card or a Network Card, including LAN software, are also required for SIS integration with your Dealer Business System.A Fully Integrated SIS Workstation is a computer system setup with the ability to tie into your Dealer Business System (DBS), and perform business functions such as parts ordering and warranty reporting. There are specific hardware and software requirements for putting together a workstation with this capability.The Deluxe SIS TechStation and the Deluxe SIS/Multimedia TechStations, with or without a printer, meet most of the hardware, and some of the software requirements for an integrated workstation. Deluxe SIS TechStations:In order for the Deluxe SIS TechStations to fulfill all of the hardware requirements, either a 5250 emulation card or a network card for integrating the TechStation to your DBS will need to be added along with an interface cable between the card and the external connector panel on the TechStation. The type of network will determine the type of network card. The most commonly used network cards are the IBM 16/4 Token Ring or the Ethernet card.In order to determine which cable assembly will be required for connecting the network card (internal to the PC) to the rear connector panel on the TechStation, refer to the previous section on Caterpillar Hardware Accessories for part numbers. If a 5250 emulation card is used instead of a network card, the 128-3259 Adapter Cable will interface it to the rear connector panel on the TechStation.In order for the Deluxe SIS TechStations to fulfill all of the software requirements, the following software programs will need to be added.1.