2058025 PLATE & FILM GP Caterpillar parts
Rating:
Alternative (cross code) number:
CA2058025
205-8025
2058025
CA2058025
205-8025
2058025
Number on catalog scheme:
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Description Qty
A 4C-5599 Anti-Seize Compound 1
B 2P-2333 High Temperature Sealer 1
C 165-4638 Guide 3 Start By:
Remove the low-pressure turbocharger.
Remove the high-pressure turbocharger.
Remove the exhaust gas cooler.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02130391
Remove five bolts (1) and remove bolt (4).
Remove bolts (3) and remove bracket (2).
Illustration 2 g02353051
Remove nuts (6) and remove spacers (5). Discard all nuts (6). Remove exhaust manifold assembly (7).
Illustration 3 g02353052
Separate exhaust manifold sections (8), (9), and (10).Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replacethe components, if necessary.
Install the exhaust manifold in the reverse order.
Apply a thin coat of Tooling (B) to the outside of the male ends that are on manifold sections (8) and (10). Assemble manifold sections (8), (9), and (10).
Illustration 4 g02353051
Illustration 5 g01381130
Torque Sequence
Apply Tooling (A) on the threads of new nuts (6). Install Tooling (C) at Location (X). Position spacers (5) and install nuts (6). Hand tighten nuts (6). Remove Tooling (C). Install remaining spacers (5) and nuts (6). Tighten nuts (6) in the above sequence to a torque of 20 3 N m (15 2. lb ft). Tighten nuts (6) again in the same sequence to torque of 50 5 N m (37 4 lb ft).
Table 1
Required Tools
Tool Part Number Description Qty
A 4C-5599 Anti-Seize Compound 1
B 2P-2333 High Temperature Sealer 1
C 165-4638 Guide 3 Start By:
Remove the low-pressure turbocharger.
Remove the high-pressure turbocharger.
Remove the exhaust gas cooler.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g02130391
Remove five bolts (1) and remove bolt (4).
Remove bolts (3) and remove bracket (2).
Illustration 2 g02353051
Remove nuts (6) and remove spacers (5). Discard all nuts (6). Remove exhaust manifold assembly (7).
Illustration 3 g02353052
Separate exhaust manifold sections (8), (9), and (10).Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replacethe components, if necessary.
Install the exhaust manifold in the reverse order.
Apply a thin coat of Tooling (B) to the outside of the male ends that are on manifold sections (8) and (10). Assemble manifold sections (8), (9), and (10).
Illustration 4 g02353051
Illustration 5 g01381130
Torque Sequence
Apply Tooling (A) on the threads of new nuts (6). Install Tooling (C) at Location (X). Position spacers (5) and install nuts (6). Hand tighten nuts (6). Remove Tooling (C). Install remaining spacers (5) and nuts (6). Tighten nuts (6) in the above sequence to a torque of 20 3 N m (15 2. lb ft). Tighten nuts (6) again in the same sequence to torque of 50 5 N m (37 4 lb ft).