AVSPARE.COM
parts catalog

PLATE AS 2389687 - Caterpillar



2389687 PLATE AS Caterpillar parts 950H PLATE
Rating:
26
Alternative (cross code) number:
CA2389687
238-9687
2389687
Caterpillar 2389687 PLATE AS

Buy PLATE AS 2389687 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 2389687:

WHEEL LOADER  950H   Caterpillar
Number on catalog scheme: 3
 
  For full view, you need register

Information:


Illustration 1 g02162093
Schematic of the auxiliary lever #1 position sensorThis diagnostic code is associated with the auxiliary lever #1 position sensor. This diagnostic code is recorded when the ECM reads the sensor signal as being below normal. The possible causes of this diagnostic code are listed:
The sensor supply wire is open.
The signal circuit is shorted to ground.
The sensor has failed.
The ECM has failed. The failure of the ECM is unlikely. Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure, and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.Note: Ensure that CID 2204 FMI 04 is active. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected.Test Step 1. CHECK THE SENSOR.
Turn the key start switch to the ON position.
Ensure that the diagnostic code is active.
Disconnect the sensor from the machine harness.
Observe the status of the diagnostic code. Expected Result:The diagnostic code will remain active.Results:
OK - The diagnostic code remains active. The sensor has not failed. The machine harness may have failed or the ECM may have failed. Proceed to test step 2.
NOT OK - The diagnostic code is NO longer active. The sensor has failed.Repair: Replace the sensor. Recalibrate if necessary. Refer to Testing and Adjusting, "Calibration" procedure. Verify that the new sensor corrects the problem.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT TO GROUND.
The sensor remains disconnected from the machine harness.
Disconnect the negative battery cable and turn the key start switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the J1 machine harness connector, measure the resistance from contact J1-22 (wire P996-GN) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:The resistance is greater than 5000 ohms for each measurement.Results:
OK - The resistance is greater than 5000 ohms for each measurement.Repair: The ECM may have failed. Exit this procedure and perform this procedure again. If the cause of the diagnostic code is not found, contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacement, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
NOT OK - The resistance is less than 5000 ohms for one or more of the measurements.Repair: The machine harness has failed. There is a short in the machine harness between the signal circuit and ground. Repair the machine harness or replace the machine harness.STOP

Caterpillar parts catalog:

Caterpillar parts catalog
950H Wheel Loader N1A00001-UP (MACHINE) POWERED BY C7 Engine


Parts plate Caterpillar catalog:

1077694 PLATE-THRUST
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 135H, 135H NA, 140G, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 2290, 2390, 2...
9S2260 PLATE-COVER
120G, 120H, 120H ES, 120H NA, 12G, 12H ES, 12H NA, 130G, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 16G, 16H NA, 235, 3114, 3116, 3126, 3126B, 317...
6H5139 PLATE-PRESSURE
120G, 12F, 12G, 130G, 140, 141, 14E, 14G, 153, 16, 163, 16G, 172, 173B, 183, 183B, 184, 191, 193, 30/30, 416, 416B, 426B, 428, 428B, 438B, 446, 46, 508, 515, 517, 518, 525, 525D, 527, 528, 535D, 545D,...
1P6356 PLATE
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 1390, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, ...
2D4202 PLATE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160G, 160H, 160H ES, 160H NA, 160K, ...
9C9159 PLATE
3512B, 3516B, 3516C, 587T, 814B, 814F, 815B, 815F, 816F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966D, 966F, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 970F, 972G,...
1960225 PLATE
725, 725C, 730, 730C, 769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM, 784C, 785C, 785D, 834K, 836K, 844, 9...
7G0437 PLATE-CLUTCH
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14M, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16M, 517, 527, 561M, 561N, ...
6P7968 PLATE-CLUTCH
517, 518, 527, 561M, 561N, 613C, 613C II, 613G, 931B, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, 966R, D4H XL, D4HTS...
8E1666 PLATE-RETAINER
517, 527, 561M, 561N, 936, 936F, 950B, 950B/950E, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966H, 966K, 966M, D4H XL, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D5...
8E5311 PLATE-CORNER
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966F II, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, 973C, 973D, 980K
1343079 PLATE
525B, 525C, 535B, 535C, 545C, 824K, 825K, 950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, IT62G, IT62G II, IT6...
3345849 PLATE-WEAR
950H, 962H, 966H, 966K, 972H, 972K
3239141 PLATE-WEAR
950H, 962H, 966H, 966K, 972H, 972K
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.