2396486 PLATE Caterpillar parts
330D, 330D L, 330D LN, 330D MH, 336D2, M330D
Rating:
Alternative (cross code) number:
CA2396486
239-6486
2396486
CA2396486
239-6486
2396486
Weight: 4 pounds 2 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 2396486:
Number on catalog scheme:
4
For full view, you need register
Information:
If the measurement is not within this range, adjustment is necessary. Refer to Testing and Adjusting, "Valve Lash Adjustment".Valve Lash Adjustment
Illustration 1 g01469728
3408E Engines (A) Inlet valves (B) Exhaust valves (C) Left side of the engine (D) Cylinder number (E) Flywheel end of the engine (F) Front of the engine (G) Right side of the engine
Illustration 2 g01469727
3412E Engines (A) Inlet valves (B) Exhaust valves (C) Left side of the engine (D) Cylinder number (E) Flywheel end of the engine (F) Front of the engine (G) Right side of the engineNumber one cylinder is the front cylinder on the left side of the cylinder block.Number two cylinder is the front cylinder on the right side of the cylinder block.Note: The front of the engine is opposite of the flywheel end of the engine. The left side of the engine and the right side of the engine are viewed from the flywheel end of the engine.
Illustration 3 g00506544
Valve lash check (1) Valve adjustment locknut (2) Exhaust adjustment screw (3) Valve adjustment locknut (4) Inlet adjustment screw (5) Feeler gauge
Table 4
Valve Lash
Valves Thickness of Gauge
Inlet
0.38 mm (0.015 inch)
Exhaust
0.76 mm (0.030 inch) Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position.Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves.Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshafts base circle.
Make the adjustment to the valve lash on the inlet valves for the following cylinders by using the 194-2062 Valve Adjusting Tool Gp .For 3408E Engines, adjust the valve lash on the inlet valves for cylinders 1, 2, 5, and 7.For 3412E Engines, adjust the valve lash on the inlet valves for cylinders 1, 3, 4, 6, 7, and 12.
Loosen valve adjustment locknut (3) .
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 4.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 4 N m (22 3 lb ft). Recheck each adjustment.
Make the adjustment to the valve lash on the exhaust valves for the following cylinders by using the 194-2062 Valve Adjusting Tool Gp .For 3408E Engines, adjust the valve lash on the exhaust valves for cylinders 1, 3, 4, and 8.For 3412E Engines, adjust the valve lash on the exhaust valves for cylinders 1, 4, 5, 8, 9, and 12.
Loosen valve adjustment
Illustration 1 g01469728
3408E Engines (A) Inlet valves (B) Exhaust valves (C) Left side of the engine (D) Cylinder number (E) Flywheel end of the engine (F) Front of the engine (G) Right side of the engine
Illustration 2 g01469727
3412E Engines (A) Inlet valves (B) Exhaust valves (C) Left side of the engine (D) Cylinder number (E) Flywheel end of the engine (F) Front of the engine (G) Right side of the engineNumber one cylinder is the front cylinder on the left side of the cylinder block.Number two cylinder is the front cylinder on the right side of the cylinder block.Note: The front of the engine is opposite of the flywheel end of the engine. The left side of the engine and the right side of the engine are viewed from the flywheel end of the engine.
Illustration 3 g00506544
Valve lash check (1) Valve adjustment locknut (2) Exhaust adjustment screw (3) Valve adjustment locknut (4) Inlet adjustment screw (5) Feeler gauge
Table 4
Valve Lash
Valves Thickness of Gauge
Inlet
0.38 mm (0.015 inch)
Exhaust
0.76 mm (0.030 inch) Adjust the valve lash while the engine is stopped. Use the following procedure in order to adjust the valves:
Put the No. 1 piston at the top center position.Note: See Testing and Adjusting, "Finding Top Center Position for the No. 1 Piston" for further details.
With No. 1 piston at the top center position of the compression stroke, an adjustment can be made to the valves.Before any adjustments are made, lightly tap each rocker arm at the top of the adjustment screw. Use a soft mallet to ensure that the lifter roller seats against the camshafts base circle.
Make the adjustment to the valve lash on the inlet valves for the following cylinders by using the 194-2062 Valve Adjusting Tool Gp .For 3408E Engines, adjust the valve lash on the inlet valves for cylinders 1, 2, 5, and 7.For 3412E Engines, adjust the valve lash on the inlet valves for cylinders 1, 3, 4, 6, 7, and 12.
Loosen valve adjustment locknut (3) .
Place the appropriate feeler gauge (5) between the inlet rocker arm and the inlet valve bridge. Turn inlet adjustment screw (4) while valve adjustment locknut (3) is being held from turning. Adjust the valve lash until the correct specification is achieved. Refer to Table 4.
After each adjustment, tighten valve adjustment locknut (3) while valve adjustment screw (4) is being held from turning. Tighten to a torque of 30 4 N m (22 3 lb ft). Recheck each adjustment.
Make the adjustment to the valve lash on the exhaust valves for the following cylinders by using the 194-2062 Valve Adjusting Tool Gp .For 3408E Engines, adjust the valve lash on the exhaust valves for cylinders 1, 3, 4, and 8.For 3412E Engines, adjust the valve lash on the exhaust valves for cylinders 1, 4, 5, 8, 9, and 12.
Loosen valve adjustment
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
120H, 12H, 135H, 140H, 143H, 14H, 160H, 163H, 16H, 330D L, 330D LN, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 651E...
330D L, 330D LN, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 797, W345B II, W345C MH
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322B L, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325D, 32...
320 L, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 328D LCR, 329D, 329D L, 329D L...
115, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B L, 325C, 325D, 325D L, 326D L, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 330, 330 L, 330B, 330B L, 330C, 330C L, 330D, 330D L, 330...
324D L, 325D L, 328D LCR, 329D L, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E L, 336E LN, 340D L, 340D2 L, 345B II, 345B L, 345C, 345C L, 345D, 345D L, 345D L VG, ...
325, 325 L, 325 LN, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 3...
2653537
PLATE AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2813546
PLATE AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
2396500
PLATE
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2154102
PLATE
323D L, 325D, 329D L, 345C L, OEMS
323D L, 325D, 329D L, 345C L, OEMS
2154101
PLATE
323D L, 325D, 329D L, 345C L, OEMS
323D L, 325D, 329D L, 345C L, OEMS
1866014
PLATE
325D, 329D L, 330D, 336D L, 336D LN, 336E, 345C L, OEMS
325D, 329D L, 330D, 336D L, 336D LN, 336E, 345C L, OEMS
2709617
PLATE AS
330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 336D2, M330D
330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 336D2, M330D
2622360
PLATE AS-GUARD
330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 336D2, M330D
330D, 330D L, 330D LN, 330D MH, 336D L, 336D LN, 336D2, M330D
2276101
PLATE-WASHER
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH
325C, 328D LCR, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH
2977713
PLATE AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, M330D
2552991
PLATE AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, M330D
3109725
PLATE
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D