AVSPARE.COM
parts catalog

PLATE GP-SCREED 2501070 - Caterpillar



2501070 PLATE GP-SCREED Caterpillar parts AS2301 PLATE
Rating:
19
Alternative (cross code) number:
CA2501070
250-1070
2501070
Caterpillar 2501070 PLATE GP-SCREED

Buy PLATE GP-SCREED 2501070 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT SCREED,

Compatible equipment models: 2501070:

ASPHALT SCREED  AS2301   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 363-4046 Piston Ring Compressor 1
B 4C-5593 Anti-Seize Compound 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Apply clean engine oil to the pistons, the piston rings, and the cylinder bore.
Illustration 1 g02162176
Position the piston rings so that the end gaps are located 120 degrees from each other. Install Tooling (A) in order to compress the piston rings. When installing tooling (A), ensure that the tooling is positioned above the piston skirt which is marked (C). Note: Install the piston and connecting rod so that the forging number on the connecting rod points toward the flywheel end of the engine.
With the number one crankshaft throw at the bottom center, install the piston and connecting rod in the engine. Ensure that the proper piston and connecting rod are in the corresponding cylinder with the bearing retainer notch toward the right side of the engine.
Line up the piston and the connecting rod with the crankshaft. Use a soft faced hammer and tap the piston into the cylinder bore until Tooling (A) comes off the piston.
Illustration 2 g01261959
Illustration 3 g01261956
Before connecting rod (3) comes in contact with the crankshaft, install the upper half of connecting rod bearing (4). Ensure that the bearing tab engages with the slot in connecting rod (3).
Apply clean engine oil to the surface of the upper half of connecting rod bearing (4). Use a soft faced hammer in order to tap the piston into the cylinder bore while you guide connecting rod (3) onto the crankshaft.
Place the lower half of connecting rod bearing (4) in corresponding connecting rod cap (2). Ensure that the bearing tab engages with the groove in connecting rod cap (2).
Apply clean engine oil to the surface of the lower half of connecting rod bearing (4). Install connecting rod bearing cap (2) on connecting rod (3). Ensure that the number on connecting rod cap (2) matches the number on connecting rod (3). Ensure that the numbers are on the same side.
Lubricate the new connecting rod bolts with Tooling (B).
Install new bolts (1). Tighten bolts (1) to a torque of 50 5 N m (37 4 lb ft).
Place an index mark on each bolt. Tighten each bolt (1) for an additional 90 5 degrees (1/4 turn). End By:
Install the piston cooling jets.
Install the engine oil pump.
Install the cylinder head.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
AS2301 Screed AWC00001-UP


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.