2902871 PLATE-WEAR Caterpillar parts
365B II
Rating:
Alternative (cross code) number:
CA2902871
290-2871
2902871
CA2902871
290-2871
2902871
EXCAVATOR,
Compatible equipment models: 2902871:
Number on catalog scheme:
5
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
In order to remove the connecting rod caps, rotate the crankshaft in a clockwise direction until the piston is at the bottom center position.
Illustration 1 g00970465
Illustration 2 g00974873
Inspect the connecting rod (5) and connecting rod cap (2) for the proper identification mark. The connecting rod and the connecting rod cap should have an etched Number (Y) on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.
Remove the setscrews (1) from the connecting rod (5). Remove the connecting rod cap (2). Remove the lower connecting rod bearing (3) from the connecting rod cap. Note: Do not reuse the setscrews (1). Use new setscrews in order to secure the connecting rod cap for reassembly.
Carefully push the connecting rod into the cylinder bore. Remove the upper connecting rod bearing (4) from the connecting rod. Note: Do not allow the connecting rod to contact the piston cooling jet.
Repeat Steps 1 through 4 for the remaining connecting rod bearings.
Start By:
Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove and Install".
Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
In order to remove the connecting rod caps, rotate the crankshaft in a clockwise direction until the piston is at the bottom center position.
Illustration 1 g00970465
Illustration 2 g00974873
Inspect the connecting rod (5) and connecting rod cap (2) for the proper identification mark. The connecting rod and the connecting rod cap should have an etched Number (Y) on the side. The number should match the cylinder number. Mark the connecting rod and the connecting rod cap, if necessary.
Remove the setscrews (1) from the connecting rod (5). Remove the connecting rod cap (2). Remove the lower connecting rod bearing (3) from the connecting rod cap. Note: Do not reuse the setscrews (1). Use new setscrews in order to secure the connecting rod cap for reassembly.
Carefully push the connecting rod into the cylinder bore. Remove the upper connecting rod bearing (4) from the connecting rod. Note: Do not allow the connecting rod to contact the piston cooling jet.
Repeat Steps 1 through 4 for the remaining connecting rod bearings.
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 235, 235D, 2390, 2391, 245, 2491...
140H, 143H, 14H, 14M, 160H, 163H, 16H, 16M, 3176C, 3196, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 3...
345C, 345C L, 345C MH, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 5090B, 5110B, 824G II, 824H, 825G II, 825H, 826G II, 826H, 834H, 83...
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311D LRR, 311F LRR, 312C, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR...
235D, 365B, 365B II, 740, 740B, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 775B, 775D, 776C, 776D, 777D, 824G II, 824H, 834B, 834G, 834H, 836, 836G, 836H, 844, 844H, 844K, 854G, 854K, 950F, 950F II, 95...
330C, 345C, 345C L, 345D L, 345D L VG, 365B, 365B II, 365B L, 365C, 365C L, 374D L, 374F L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 390D, 390D L, 390F L, 5080
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
345C, 345C L, 345C MH, 345D L, 365B, 365B II, 365B L, 365C, 365C L, 385B, 385C, 385C L, PIN GRAB, W345C MH
2952639
PLATE AS-BOX
365B II
365B II
2902869
PLATE-REINFORCEMENT
365B II
365B II
2902870
PLATE-WEAR
365B II
365B II
2902864
PLATE-WEAR
365B II, 365C
365B II, 365C
2952638
PLATE AS-BOX
365B II
365B II
3463097
PLATE
365B II, 365C
365B II, 365C
2902880
PLATE-WEAR
365B II
365B II
2952641
PLATE AS-BOX
365B II
365B II
2904213
PLATE-REINFORCEMENT
365B II, 365C
365B II, 365C
2924216
PLATE-WEAR
365B II, 365C
365B II, 365C
2952640
PLATE AS-BOX
365B II, 365C
365B II, 365C
2924212
PLATE-REINFORCEMENT
365B II
365B II