AVSPARE.COM
parts catalog

PLATE 2H9147 - Caterpillar



2H9147 PLATE Caterpillar parts D337 PLATE
Rating:
24
Alternative (cross code) number:
CA2H9147
2H-9147
2H9147
Caterpillar 2H9147 PLATE

Buy PLATE 2H9147 Caterpillar genuine, new aftermarket tractor parts with delivery
MARINE ENGINE,

Compatible equipment models: 2H9147:

MARINE ENGINE  D337   Caterpillar
Number on catalog scheme:
 
  For full view, you need register

Information:

1. Before the cab is lowered, be sure the lever on the governor and the governor control lever in the cab are both in the "FUEL OFF" position.2. Use this procedure to lower the cab to the 24° position if the machine has a ROPS or cab, and an overhead hoist is available. a. Fasten an overhead hoist to tooling (A) on the side of the cab. b. Remove bolt (1) from the plate and bracket on the front of the cab. c. As the cab is lowered, hold bar (3) for the governor control in alignment with tube (2) so the bar will slide into the tube. d. Lower the cab until bolts (5) can be installed in the support bracket.e. Install pin (4) in the rod end of the cylinder jack.f. Remove tooling (A) from the cab, and install the original bolt in the cab. Tighten bolts to a torque of 360 50 kg (265 35 lb.ft.). 3. Use this procedure to lower the cab to the 24° position if the machine has a ROPS or cab and an overhead hoist is not available.a. On earlier style cabs with lifting eyes, fasten tooling (B) and a hoist to the cab and the bucket levers as shown. Later style cabs do not have lifting eyes. The link brackets from tooling (E) are installed in the air conditioner mounting bosses. Install tooling (E). In both cases, fasten tooling (C) to the rear of the cab.
Do not lower the cab beyond the 24° position with tooling (B) or (E). Tooling (B) or (E) will be overloaded and a failure of the tooling will permit the cab to fall which can cause personal injury. To prevent injury, never lower the cab beyond the 24° position with tooling (B) or (E).
b. Remove bolt (1) from plate and bracket. Use tooling (B) or (E) and (C) to lower the cab to the 24° position. c. As the cab is lowered, hold bar (3) for the governor control in alignment with tube (2) so the bar will slide into the tube. d. Lower the cab until bolts (5) can be installed in the support bracket. Remove tooling (C). e. Put rod end (6) of the jack in position on the cab, and install the pin. Remove tooling (B).
Typical Example4. Use this procedure to lower the platform to the 24° position if the machine does not have a ROPS or cab.a. Fasten tooling (D) to the platform and the bucket levers.b. Install tooling (A) and the overhead hoist. Lift the hoist so the chain to tooling (A) is tight. c. Use tool (D) to pull the platform forward so bolt (1) can be removed from the plate and bracket. Release tool (D) so the overhead hoist holds the weight of the platform.
Do not use tooling (D) to lower the platform. The platform in the lower position will overload the tooling and cause a failure which will permit the cab to fall. To

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455


Parts plate Caterpillar catalog:

2F2006 PLATE
955C, D315, D337, D342, D364, D375D, D379, D379A, D397D, D398, D398A, D399, D8H, G379, G398
8F4102 PLATE
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12E, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M ...
4F2288 PLATE
D315, D337, D397D
5H9247 PLATE
955C, D326F, D337
1H1063 PLATE SERIAL NUMBER
1693, 3145, 3150, 3304, D326F, D330A, D337, D337F, D342, D342C, D346, D348, D353C, D364, D375D, D397D, D398A
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.