3040040 PLATE Caterpillar parts
345C, 345C L, 345C MH, 345D L, W345C MH
Rating:
Alternative (cross code) number:
CA3040040
304-0040
3040040
CA3040040
304-0040
3040040
Weight: 1 pounds 0 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$0.79
05 Jul 2018
Arctic Cat: Arctic Cat
Arctic Cat Washer Cylinder Head Bolt 3040-040 New OEM
New OEM Arctic Cat Washer Cylinder Head Bolt || OEM Part Number: 3040-040 || Item only fits specific models listed. The picture could be generic. || Message us with VIN/HULL for fast fitment verification.
New OEM Arctic Cat Washer Cylinder Head Bolt || OEM Part Number: 3040-040 || Item only fits specific models listed. The picture could be generic. || Message us with VIN/HULL for fast fitment verification.
Number on catalog scheme:
18
For full view, you need register
Compatible equipment models: 3040040:
Information:
Test Procedure (Accumulator Charge Pressure)
Move the machine to a smooth horizontal location.
Lower all of the implements. Engage the parking brake. Stop the engine.
Illustration 2 g01371313
Illustration 3 g01225243
(1) Accumulator (2) Transmission (3) Valve (4) Protector
Remove protector (4). Attach tooling (C6), (C7), (C10), and (C11) to valve (3) .
The accumulator charge pressure at tooling (C7) should be 1725 100 kPa (250 15 psi) when the oil temperature is 20 °C (70 °F). If the pressure of the accumulator is low then the accumulator needs to be charged. Check the accumulator again in order to ensure that the charge is maintained.Charging Procedure
Dry nitrogen is the only gas approved for use in the accumulator. Charging the accumulator with oxygen gas will cause an explosion. This danger will not happen if nitrogen cylinders with standard CGA (Compressed Gas Association, Inc.) Number 580 connections are used. When you order nitrogen gas, be sure that the cylinders are equipped with CGA No. 580 Connections. Do not use color codes or other methods of identification to tell the difference between nitrogen and oxygen cylinders.
A new accumulator should be charged before installation. Do not charge an accumulator that is connected to a power train system. Pressure from the power train oil in the system may interfere with the charging procedure.Gas pressure is variable with the temperature. The accumulator must be at the same temperature as the surrounding air before the accumulator can be charged. Use the following chart for the correct nitrogen charge. Use dry nitrogen.
Table 2
Charging Pressure for the Accumulator at Different Oil Temperatures
Temperature Pressure
16 °C (60 °F)
1690 kPa (245 psi)
21 °C (70 °F)
1725 kPa (250 psi)
27 °C (80 °F)
1760 kPa (255 psi)
Illustration 4 g01099041
175-5507 Nitrogen Charging Group (C6) Needle Valve (C7) Pressure Gauge (C8) Regulator (C9) Nitrogen Charging Chuck (C10) Nitrogen Charging Chuck (7) Screw (8) Pressure Gauge
Connect the 175-5507 Nitrogen Charging Group to the nitrogen cylinder at nitrogen charging chuck (C9) .
Make sure that needle valve (C6) is closed. Open the valve on the nitrogen cylinder.
Illustration 5 g01225244
(1) Accumulator (3) Valve (4) Protector
Remove protector (4) from valve (3) of accumulator (1) .
Install nitrogen charging chuck (C10) on valve (3) .
Open the valve handle on nitrogen charging chuck (C10). Use pressure gauge (C7) in order to monitor the nitrogen charge in the accumulator.
Check the temperature of the air around the accumulator. Refer to Table 2 for the correct charging pressure.
Open the valve on the nitrogen cylinder. Adjust screw (7) on regulator (C8) until pressure gauge (8) is at the pressure that will charge the accumulator.
Open needle valve (C6) in order to allow nitrogen to flow into the accumulator.
When the pressures on pressure gauge (C7) and on pressure gauge (8) are identical, turn off regulator (C8) .
If the pressure on pressure gauge (C7) decreases, open regulator (C8) .
Repeat Steps 9 and 10 until you have the following results:
Pressure readings on pressure gauge (C7) and on pressure gauge (8) are identical.
Pressure
Move the machine to a smooth horizontal location.
Lower all of the implements. Engage the parking brake. Stop the engine.
Illustration 2 g01371313
Illustration 3 g01225243
(1) Accumulator (2) Transmission (3) Valve (4) Protector
Remove protector (4). Attach tooling (C6), (C7), (C10), and (C11) to valve (3) .
The accumulator charge pressure at tooling (C7) should be 1725 100 kPa (250 15 psi) when the oil temperature is 20 °C (70 °F). If the pressure of the accumulator is low then the accumulator needs to be charged. Check the accumulator again in order to ensure that the charge is maintained.Charging Procedure
Dry nitrogen is the only gas approved for use in the accumulator. Charging the accumulator with oxygen gas will cause an explosion. This danger will not happen if nitrogen cylinders with standard CGA (Compressed Gas Association, Inc.) Number 580 connections are used. When you order nitrogen gas, be sure that the cylinders are equipped with CGA No. 580 Connections. Do not use color codes or other methods of identification to tell the difference between nitrogen and oxygen cylinders.
A new accumulator should be charged before installation. Do not charge an accumulator that is connected to a power train system. Pressure from the power train oil in the system may interfere with the charging procedure.Gas pressure is variable with the temperature. The accumulator must be at the same temperature as the surrounding air before the accumulator can be charged. Use the following chart for the correct nitrogen charge. Use dry nitrogen.
Table 2
Charging Pressure for the Accumulator at Different Oil Temperatures
Temperature Pressure
16 °C (60 °F)
1690 kPa (245 psi)
21 °C (70 °F)
1725 kPa (250 psi)
27 °C (80 °F)
1760 kPa (255 psi)
Illustration 4 g01099041
175-5507 Nitrogen Charging Group (C6) Needle Valve (C7) Pressure Gauge (C8) Regulator (C9) Nitrogen Charging Chuck (C10) Nitrogen Charging Chuck (7) Screw (8) Pressure Gauge
Connect the 175-5507 Nitrogen Charging Group to the nitrogen cylinder at nitrogen charging chuck (C9) .
Make sure that needle valve (C6) is closed. Open the valve on the nitrogen cylinder.
Illustration 5 g01225244
(1) Accumulator (3) Valve (4) Protector
Remove protector (4) from valve (3) of accumulator (1) .
Install nitrogen charging chuck (C10) on valve (3) .
Open the valve handle on nitrogen charging chuck (C10). Use pressure gauge (C7) in order to monitor the nitrogen charge in the accumulator.
Check the temperature of the air around the accumulator. Refer to Table 2 for the correct charging pressure.
Open the valve on the nitrogen cylinder. Adjust screw (7) on regulator (C8) until pressure gauge (8) is at the pressure that will charge the accumulator.
Open needle valve (C6) in order to allow nitrogen to flow into the accumulator.
When the pressures on pressure gauge (C7) and on pressure gauge (8) are identical, turn off regulator (C8) .
If the pressure on pressure gauge (C7) decreases, open regulator (C8) .
Repeat Steps 9 and 10 until you have the following results:
Pressure readings on pressure gauge (C7) and on pressure gauge (8) are identical.
Pressure
Caterpillar parts catalog:
Parts plate Caterpillar catalog:
1960778
PLATE
330C, 330C L
330C, 330C L
1960777
PLATE
330C, 330C L
330C, 330C L
2292459
PLATE
330C, 330C L
330C, 330C L
2241716
PLATE
330C, 330C L
330C, 330C L
2189381
PLATE
330C, 330C L
330C, 330C L
2033443
PLATE AS
330C, 330C L
330C, 330C L
1327298
PLATE
330C, 330C L, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D L, 345D L VG, 349D L, 349E, 349E L, 349E L VG
330C, 330C L, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D L, 345D L VG, 349D L, 349E, 349E L, 349E L VG
1327297
PLATE
330C, 330D L, 345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L VG
330C, 330D L, 345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L VG
1327295
PLATE AS
330C, 330D L, 345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L VG
330C, 330D L, 345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D L, 349E L VG
1401495
PLATE AS
325D MH, 330D, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, M325D L MH, M330D, W345B II, W345C MH
325D MH, 330D, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, M325D L MH, M330D, W345B II, W345C MH
4I2509
PLATE-END
345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C L, ...
345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L, 350, 350 L, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C L, ...
1461332
PLATE
345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L
345B II, 345B L, 345C, 345C L, 345D, 345D L, 349D, 349D L, 349E L, 349E L VG, 349F L