3080714 PLATE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA3080714
308-0714
3080714
CA3080714
308-0714
3080714
Information:
The fuel temperature has exceeded the trip point and the delay time has expired. The Electronic Control Module (ECM) will reset the warning when the fuel temperature is above the reset value.The ECM detects all of the following conditions:
The engine has been running at least three minutes. This three minute delay begins once the engine speed is within 50 rpm of the low idle setting.
Diagnostic code 0174-02 is not active.System Response:The ECM will log the event. The event code can be viewed on the diagnostic screen of the electronic service tool.Troubleshooting:
There may be a problem with the fuel system.
There may be a problem with the fuel temperature sensor.Test Step 1. Check for Diagnostic Codes
Connect the electronic service tool to the diagnostic connector.
Turn the keyswitch to the ON position. Do not start the engine.
Check for any active diagnostic codes or logged diagnostic codes. Expected Result:There should be no diagnostic codes that are present.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the fault that has generated the diagnostic code. Refer to the appropriate topic in Troubleshooting, "Troubleshooting with a Diagnostic Code".Ensure that the repair has eliminated the fault.STOPTest Step 2. Check the Fuel System
Perform a check of the fuel system. Refer to the appropriate topic in Systems Operation, Testing and Adjusting for possible causes. Expected Result:There are no faults in the fuel system.Results:
OK - There may be an intermittent fault.Repair: Monitor the operation of the engine.If an intermittent fault is identified, repair the fault.Ensure that the repair has eliminated the fault.STOP
Not OK - Repair: Perform a further investigation of the fault.Ensure that any repair has eliminated the fault.STOP
The engine has been running at least three minutes. This three minute delay begins once the engine speed is within 50 rpm of the low idle setting.
Diagnostic code 0174-02 is not active.System Response:The ECM will log the event. The event code can be viewed on the diagnostic screen of the electronic service tool.Troubleshooting:
There may be a problem with the fuel system.
There may be a problem with the fuel temperature sensor.Test Step 1. Check for Diagnostic Codes
Connect the electronic service tool to the diagnostic connector.
Turn the keyswitch to the ON position. Do not start the engine.
Check for any active diagnostic codes or logged diagnostic codes. Expected Result:There should be no diagnostic codes that are present.Results:
OK - Proceed to Test Step 2.
Not OK - Repair: Repair the fault that has generated the diagnostic code. Refer to the appropriate topic in Troubleshooting, "Troubleshooting with a Diagnostic Code".Ensure that the repair has eliminated the fault.STOPTest Step 2. Check the Fuel System
Perform a check of the fuel system. Refer to the appropriate topic in Systems Operation, Testing and Adjusting for possible causes. Expected Result:There are no faults in the fuel system.Results:
OK - There may be an intermittent fault.Repair: Monitor the operation of the engine.If an intermittent fault is identified, repair the fault.Ensure that the repair has eliminated the fault.STOP
Not OK - Repair: Perform a further investigation of the fault.Ensure that any repair has eliminated the fault.STOP
Parts plate Caterpillar catalog:
3080226
PLATE-COVER
Caterpillar
Caterpillar
3079862
PLATE
Caterpillar
Caterpillar
3079575
PLATE AS.-RH
Caterpillar
Caterpillar
3079574
PLATE AS.-LH
Caterpillar
Caterpillar
3079573
PLATE AS.-RH
Caterpillar
Caterpillar
3079572
PLATE AS.-LH
Caterpillar
Caterpillar
3081844
PLATE AS
Caterpillar
Caterpillar
3081761
PLATE
Caterpillar
Caterpillar
3081601
PLATE AS
Caterpillar
Caterpillar
3081591
PLATE AS
Caterpillar
Caterpillar
3081197
PLATE -FRONT
Caterpillar
Caterpillar
3081159
PLATE
Caterpillar
Caterpillar