3207379 PLATE Caterpillar parts
Rating:
Alternative (cross code) number:
CA3207379
320-7379
3207379
CA3207379
320-7379
3207379
Weight: 3 pounds 1 kg.
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
3207379 Plate (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 4.25 lbs || Dimensions: 10-11.03-11.03 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 4.25 lbs || Dimensions: 10-11.03-11.03 in || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
Number on catalog scheme:
83
For full view, you need register
Caterpillar parts catalog:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3525 Piston Ring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Rotate the crankshaft until the bearing journals are at the bottom center. The bearing journals that are at the bottom center are for the piston installation.
Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.
Move the piston rings on the pistons until the ring openings are separated by approximately 120 degrees.
Illustration 1 g00483337
Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tool (A) in position on the cylinder block and compress the piston rings.
The "V" mark must be visible on the piston and the cylinder block. If the "V" mark is not visible, the piston must be installed with the relief for the valve positioned toward the pushrod opening in the cylinder block. Damage may result if the pistons are not installed properly.
Push the piston into the cylinder liner and out of the ring compressor.
Illustration 2 g00483701
Guide connecting rod (1) into position on the crankshaft.
Put clean engine oil (SAE 30) on the lower half of the connecting rod bearing and on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Install connecting rod cap (2) and the nuts that secure the connecting rod cap. Torque both of the nuts to 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Repeat Steps 1 through 8 for the remainder of the piston and connecting rods.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-3525 Piston Ring Compressor 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Rotate the crankshaft until the bearing journals are at the bottom center. The bearing journals that are at the bottom center are for the piston installation.
Put clean engine oil on the crankshaft journals and on the inside of the cylinder liners. Put clean engine oil on the piston rings and the connecting rod bearings.
Move the piston rings on the pistons until the ring openings are separated by approximately 120 degrees.
Illustration 1 g00483337
Put the piston in the cylinder liner with the "V" mark on the piston in alignment with the "V" mark on the cylinder block. Put tool (A) in position on the cylinder block and compress the piston rings.
The "V" mark must be visible on the piston and the cylinder block. If the "V" mark is not visible, the piston must be installed with the relief for the valve positioned toward the pushrod opening in the cylinder block. Damage may result if the pistons are not installed properly.
Push the piston into the cylinder liner and out of the ring compressor.
Illustration 2 g00483701
Guide connecting rod (1) into position on the crankshaft.
Put clean engine oil (SAE 30) on the lower half of the connecting rod bearing and on the connecting rod bolts.
When the connecting rod caps are installed, ensure that the identification marks are aligned.
Install connecting rod cap (2) and the nuts that secure the connecting rod cap. Torque both of the nuts to 40 4 N m (30 3 lb ft). Mark the position of the nuts. Tighten each nut for an additional 90 degrees (1/4 turn).
Repeat Steps 1 through 8 for the remainder of the piston and connecting rods.End By:
Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Install the engine oil pan plate. Refer to Disassembly and Assembly, "Engine Oil Pan Plate - Remove and Install".
Install the spacer plate. Refer to Disassembly and Assembly, "Spacer Plate - Remove and install".
Parts plate Caterpillar catalog:
3207374
PLATE
Caterpillar
Caterpillar
3187389
PLATE
Caterpillar
Caterpillar
3184702
PLATE-COVER
Caterpillar
Caterpillar
3178709
PLATE-MOUNTING
Caterpillar
Caterpillar
3176371
PLATE AS
Caterpillar
Caterpillar
3176364
PLATE AS
Caterpillar
Caterpillar
3261955
PLATE-COVER
Caterpillar
Caterpillar
3257720
PLATE
Caterpillar
Caterpillar
3235596
PLATE
Caterpillar
Caterpillar
3225984
PLATE
Caterpillar
Caterpillar
3220729
PLATE-COVER
Caterpillar
Caterpillar
3209274
PLATE
Caterpillar
Caterpillar