AVSPARE.COM
parts catalog

PLATE - WEAR 3236442 - Caterpillar



3236442 PLATE - WEAR Caterpillar parts PLATE
Rating:
61
Alternative (cross code) number:
CA3236442
323-6442
3236442
Caterpillar 3236442 PLATE - WEAR

Buy PLATE - WEAR 3236442 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 57 g00459138
Install metal seal ring (20) in carrier assembly (19).
Illustration 58 g00720364
Install carrier assembly (19).
Illustration 59 g06293583
Install ring gear (17).
Illustration 60 g00720388
Install three clutch plates (15) and three friction discs (16) in alternating order. Install clutch plates (15) so that the guide pins pass through the bolt holes in the clutch plates. Start with a clutch plate.
Install springs (13) and clutch plate (14). Make sure that clutch plate (14) is installed so that the small holes are over springs (13).
Illustration 61 g00459079
Install seal rings (11) and (12) on clutch piston (10).
Install clutch piston (10) in No. 6 clutch housing (6). Make sure that the lips of the seals are facing downward.
Illustration 62 g01328906
Improper assembly of parts that are spring loaded can cause bodily injury.To prevent possible injury, follow the established assembly procedure and wear protective equipment.
Install No. 6 clutch housing (6) and five bolts (9). Tighten bolts (9) until bolts (9) are snug. Remove Tooling (H).
Illustration 63 g00720411
Install the remaining bolts (9). Tighten all bolts (9) to a torque of 110 10 N m (80 7 lb ft).
Illustration 64 g00459073
Use Tooling (D) gin order to install retaining ring (8) on output shaft (7).
Illustration 65 g01328912
Typical Example
Apply 690 to 1030 kPa (100 to 150 psi) of shop air pressure into each oil passage (138) (total of six).If the clutch pistons do not move, apply a small amount of clean transmission oil in each oil passage and check for movement again. If the clutch pistons do not move, the transmission must be disassembled again so that the clutch pistons and the seal rings can be checked.Note: The mounting surfaces for the transmission modulating valves must be clean. Clean the surfaces before installation of the transmission modulating valves.
Illustration 66 g00565113
Install transmission modulating valves (29) on the transmission housing. Tighten the mounting bolts to a torque of 30 4 N m (265 35 lb in).
Connect harness assemblies which attach to transmission modulating valves (29).
Illustration 67 g00459030
The No. 6 clutch housing (6) is facing upward. Attach Tooling (A) and a suitable lifting device to the transmission planetary. The weight of the transmission planetary is approximately 545 kg (1200 lb). Use Tooling (A) and a suitable lifting device to turn the transmission planetary onto the opposite end so that the No. 1 clutch housing is facing upward.
Illustration 68 g00459007
Install plate (5).
Illustration 69 g00458960
Install drive gear (4) on the end of the input shaft.
Install retainer (2) and bolt (3).
Apply clean transmission oil on O-ring seal (1). Install O-ring seal (1) on the housing.End By:
Connect the transmission to the output transfer gears.


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.