AVSPARE.COM
parts catalog

PLATE-WEAR 3236452 - Caterpillar



3236452 PLATE-WEAR Caterpillar parts PLATE
Rating:
11
Alternative (cross code) number:
CA3236452
323-6452
3236452
Caterpillar 3236452 PLATE-WEAR

Buy PLATE-WEAR 3236452 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 3
 
  For full view, you need register

Information:

Replacement Of 6V4176 Display Unit
If one or more segments do not show the correct reading on the 6V4176 Display Unit for RPM at location (A) or DEG at location (B), the problem is most likely with the display unit at either location. Be sure to check for a good connection for each display unit. Use the procedure that follows to remove a display unit. 1 Remove the six screws (1) from front panel (2), and remove panel (2) from case (3).2 Remove the four screws (4) from the PC board, and also remove the locknuts from the two front panel switches (5) and (6). 3 Carefully lift front panel (2) from PC (printed circuit) board (7).4 To remove either display unit, (A) or (B), use a screwdriver as shown, and carefully remove the unit from its position in the PC board. Before the removal of either display unit, look carefully in the area of location (C), for some type of identification mark on the display unit and on the PC board. This needs to be done to make sure that at time of installation, the display unit will be installed correctly. At installation of a display unit, be very careful and make sure the pins on the display unit are in alignment with the socket holes.Replacement Of 6V4179 Digital Voltmeter Integrated Circuit
If one or more segments of either 6V4176 Display Unit, RPM or DEG [location (A) or (B)] do not work, see REPLACEMENT OF 6V4176 DISPLAY UNIT. After a display unit has been checked and/or a replacement installed and there is still a problem; or, if one display unit is completely blank while the other one works normally, the problem can be with a 6V4179 Digital Voltmeter (DVM) Integrated Circuit. There are two 6V4179 DVM Integrated Circuits in each 6V3100 Timing Indicator. 1 Remove six screws (1), then remove panel (2) from case (3). 2 Use the hook end of 5P1720 Seal Pick (4) and carefully remove the DVM integrated circuit, (5) or (6), as shown. [Use the notch at end (A) of the DVM as a reference mark to be used at time of installation.] At installation of a DVM, put the reference mark, as given in step 2, in the correct location. Also, be sure that the pins on the DVM are in alignment with the holes in the socket.Parts And Repair Service Information
When one of the parts used with the timing indicator group is to be returned for a repair or warranty service, always give the following information: 1. Description of the type of problem.2. Where to send part after repair.3. Serial number (if applicable).4. Person the part should be sent to.5. Billing address if different than shipping address.6V3100 Engine Timing Indicator Group
For electronic repair of the timing indicator group, see Special Instruction Form SEHS8135.For warranty or repair work for the 6V3100 Engine Timing Indicator Group (except for 6V2192 Injection Transducer, 6V2197 Magnetic Transducer, or 6V7910 Injection Transducer) send the indicator group to:Snap-On Tool Corporation
Midwest

Caterpillar parts catalog:

Caterpillar parts catalog
324D L Hydraulic Excavator JJG00001-UP (MACHINE) POWERED BY C-7 Engine
320D & 320D L Excavators MCH00001-UP (MACHINE) POWERED BY C6.4 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.