AVSPARE.COM
parts catalog

PLATE-WEAR 3236453 - Caterpillar



3236453 PLATE-WEAR Caterpillar parts PLATE
Rating:
16
Alternative (cross code) number:
CA3236453
323-6453
3236453
Caterpillar 3236453 PLATE-WEAR

Buy PLATE-WEAR 3236453 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 4
 
  For full view, you need register

Information:

Procedure For Hand Welding
(1) Cut off the material shown in Figure 1 from the stub spokes on the replacement rim so the chamfer is slightly less than one-half the thickness of the spoke.(2) Cut the spokes at a location about .25" (6.4) less in diameter than the rim. This will leave a separation of .12" (3.0) as shown in Figure 1.
FIGURE 1(3) Chamfer the side of the spoke adjacent to the rim chamfer at 30° so the resulting fit will be a 60° joint as shown.(4) Cut a 45° chamfer on the opposite side of the spoke. The spoke chamfers should be located to provide about .12" (3.0) flat as shown.(5) Remove all slag or other imperfections from the joints and position the hub and rim for welding. Number the spokes clockwise in a sequence of 1, 9, 6, 3, 8, 5, 2, 7 and 4. Before welding be sure the rim and hub are the same temperature (room temperature is suitable) and weld in an area free from drafts. Use dry low hydrogen electrodes conforming to AWS Specification E-7018. Do not use any electrodes exposed to the atmosphere for more than a maximum of 4 hours.(6) Using .12" (3.0) electrodes with a current setting of 120-145 amperes DC reverse polarity, weld one pass on spokes numbered 1, 2 and 3. Clean the weld and weld one pass on the same spokes with .19" (5.0) electrodes at 230-250 amperes.(7) Use .12" (3.0) electrodes at 120-145 amperes and weld one pass on spokes 4, 5, 6, 7, 8 and 9 in that order.(8) Invert the sprocket and clean the weld joint. If the gap is too small to clean, scarf out with Arcair equipment.(9) Weld spokes 1 through 9 in numerical order using .12" (3.0) electrodes at 120-145 amperes for one pass. Clean and weld 1 through 9 again using .19" (5.0) electrodes at 230-250 amperes.(10) Continue with .19" (5.0) electrodes, putting one pass at a time on each spoke in numerical order until the weld is flush. To reduce heat concentrations, do not weave the welds or completely fill one spoke at a time.(11) Invert the sprocket and continue to weld one stringer with .19" (5.0) electrodes at 230-250 amperes on each spoke 4 through 9 in numerical order.(12) Weld one pass to each of all the spokes in numerical order until each weld is flush.(13) Turn the sprocket on edge and weld the ends of each joint, rotating the sprocket each time so each joint is in a flat position. This connects the ends of the stringer beads and makes a smoother transition from the spokes to the rim.(14) Keep the sprocket off the floor in a draft-free area during the cooling period. Although cracks are not likely to occur, any found can be repaired by veeing out and welding with a .19" (5.0) electrode.Procedure For Automatic Welding
Automatic or semi-automatic welding equipment using the submerged arc method can be utilized for sprocket rim welding if provisions are

Caterpillar parts catalog:

Caterpillar parts catalog
324D L Hydraulic Excavator JJG00001-UP (MACHINE) POWERED BY C-7 Engine
320D & 320D L Excavators MCH00001-UP (MACHINE) POWERED BY C6.4 Engine


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.