AVSPARE.COM
parts catalog

PLATE - WEAR 3236455 - Caterpillar



3236455 PLATE - WEAR Caterpillar parts PLATE
Rating:
71
Alternative (cross code) number:
CA3236455
323-6455
3236455
Caterpillar 3236455 PLATE - WEAR

Buy PLATE - WEAR 3236455 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 4 g06289384
Use Tooling (C) to install retaining ring (26). Install bearing spacer (27) and retaining ring (26).
Install O-ring seal (25).
Illustration 5 g06289379
Use Tooling (C) to install retaining ring (23). Install end cover (24) and retaining ring (23) in rotating housing (16).
Illustration 6 g06289376
Lower the temperature of bearing (22).
Install bearing (22) to impeller (15).Note: The notch in bearing (22) must face downward.
Illustration 7 g06289374
Install drive gear (21) and bolts (20). Tighten bolts (20) to a torque of 105 15 N m (75 11 lb ft).
Illustration 8 g06289423
Install seal ring (40) onto carrier shaft (19).
Install seal ring (35) onto shaft (34).
Raise the temperature of inner race (36). Install inner race (36) onto shaft (34).
Install outer bearing (37).
Use Tooling (B), Tooling (D), and a suitable press to install shaft (34) and outer bearing (37) into carrier shaft (19).
Install plate (38) and retaining ring (39).
Illustration 9 g06289462
Use a suitable soft faced hammer to install carrier shaft (19) into impeller (15).
Illustration 10 g06289319
Turn impeller (15) onto the opposite side.
Use Tooling (C) to install retaining ring (17). Install stator (18) and retaining ring (17).
Illustration 11 g06289315
Use a suitable lifting device to install impeller (15) on rotating housing (16). The weight of impeller (15) is approximately 36 kg (80 lb).
Install impeller (15) and bolts (14). Tighten bolts (14) to a torque of 60 7 N m (44 5 lb ft).
Illustration 12 g06289340
Use Tooling (B) to install bearing (13). Install bearing (13) to pump drive gear (11).
Illustration 13 g06289336
Use Tooling (A) and a suitable lifting device to install torque converter housing (12) over the torque converter. The weight of torque converter housing (12) is approximately 95 kg (209 lb). Install torque converter housing (12).
Illustration 14 g00456168
Install pump drive gear (11) and drive gear shaft (10).
Install the washer and bolt (9). Tighten bolt (9) to a torque of 240 40 N m (180 30 lb ft).
Illustration 15 g06289318
Install pump drive flange (8) and bolts (7). Tighten bolts (7) to a torque of 60 12 N m (44 9 lb ft).
Illustration 16 g06289317
Install the washer and bolts (6). Tighten bolts (6) to a torque of 55 10 N.m (41 7 lb ft).
Install O-ring seal (5).
Illustration 17 g06289316
Install gear (3), retainer (2), and bolt (1). Tighten bolt (1) to a torque of 120 20 N m (90 15 lb ft).
Install the washer, the seal, and torque converter speed sensor (4). Adjust torque converter speed sensor (4) to maintain an air gap of 0.78 0.18 mm (0.031 0.007 inch). Tighten torque converter speed sensor (4) to a torque of 25 5 N m (18 4 lb ft).End By:
Connect the torque converter to the transmission and to the output transfer gears.


Parts plate Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.